If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM F1586 - 21
Standard Specification for Wrought Nitrogen Strengthened 21Chromium—10Nickel—3Manganese—2.5Molybdenum Stainless Steel Alloy Bar for Surgical Implants (UNS S31675)
| Format | Pages | Price | ||
 |
5 | $54.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 5 | $54.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
10 | $64.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More F04.12 Standards Related Products Standard References
Abstract
This specification covers the chemical composition, mechanical, and metallurgical requirements for wrought nitrogen strengthened 21chromium-10nickel-3manganese-2.5molybdenum stainless steel alloy bars for use in surgical implants. The alloy bars shall be furnished in the annealed, medium hard, or hard condition, and shall be finished cold-drawn, pickled, ground, ground and polished, or as specified by the purchaser.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers the chemical, mechanical, and metallurgical requirements for wrought nitrogen strengthened 21chromium—10nickel—3manganese—2.5molybdenum stainless steel alloy bar for surgical implants.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A751 Test Methods and Practices for Chemical Analysis of Steel Products
E8/E8M Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E45 Test Methods for Determining the Inclusion Content of Steel
E112 Test Methods for Determining Average Grain Size
F138 Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Bar and Wire for Surgical Implants (UNS S31673)
F746 Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials
ICS Code
ICS Number Code 11.040.40 (Implants for surgery, prothetics and orthotics)
UNSPSC Code
UNSPSC Code 42295500(Surgical implants and expanders and extenders and surgical wires and related products)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F1586-21
Citation Format
ASTM F1586-21, Standard Specification for Wrought Nitrogen Strengthened 21Chromium—10Nickel—3Manganese—2.5Molybdenum Stainless Steel Alloy Bar for Surgical Implants (UNS S31675), ASTM International, West Conshohocken, PA, 2021, www.astm.org
Back to Top