ASTM F1414 - 19

    Standard Test Method for Measurement of Cut Resistance to Chainsaw in Lower Body (Legs) Protective Clothing

    Active Standard ASTM F1414 | Developed by Subcommittee: F23.20

    Book of Standards Volume: 11.03

      Format Pages Price  
    PDF 15 $58.00   ADD TO CART
    Hardcopy (shipping and handling) 15 $58.00   ADD TO CART
    Standard + Redline PDF Bundle 30 $69.00   ADD TO CART

    Significance and Use

    5.1 The purpose of this test method is to provide a measurable criterion of performance about the level of cut resistance provided by different types of protective garments and protected coverings worn by chainsaw operators.

    5.2 This test method is intended to show to what level a protective garment can offer resistance to the cutting action of a chainsaw.

    5.3 The protection which can be demonstrated by the garments and coverings tested in accordance with this test method is achieved by: (1) the cut resistance of the material to cutting when put in contact with saw chain; (2) pulling a part of the material or yarns in the material so that they are drawn into the chain and drive mechanism to block the chain movement; (3) the fibers of the materials used to demonstrate both high resistance to cutting and the capacity to absorb rotational energy, so that chain speed can be slowed down sufficiently to stop the movement of the saw chain; or (4) any combination of these.

    5.4 This test method does not purport to evaluate comfort of lower body protective garments.

    5.5 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should perform comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens from the same lot of components to be evaluated. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. If a bias is found, either its cause must be determined and corrected or the purchaser and the supplier must agree to interpret future test results in light of the known bias.

    1. Scope

    1.1 This test method measures cut resistance of garments and devices worn to protect the lower body (legs) when operating a chainsaw.

    1.2 This test method may be used to test for compliance to minimum performance requirements in established safety standards.

    1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, it will be decided if this test method will be used to determine one or both of the following: (1) chain speed 50 (CS50), and (2) success/failure (jamming/chain stop or no cut in less than 1.5 s) at specified chain speed.

    1.3 This test method may be used to determine levels of protection for areas of coverage as stipulated in established safety standards.

    1.4 The values stated in SI units are to be regarded as standard.

    Note 1: The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D123 Terminology Relating to Textiles

    D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber

    D1776/D1776M Practice for Conditioning and Testing Textiles

    F1494 Terminology Relating to Protective Clothing

    Federal Standard

    FS 5100-86 Type II, Cloth, Duck, Nylon, Polyurethane Coated

    Military Standard


    ICS Code

    ICS Number Code 13.340.10 (Protective clothing)

    UNSPSC Code

    UNSPSC Code 46180000(Personal safety and protection); 27112746(Chain saw)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F1414-19

    Citation Format

    ASTM F1414-19, Standard Test Method for Measurement of Cut Resistance to Chainsaw in Lower Body (Legs) Protective Clothing, ASTM International, West Conshohocken, PA, 2019,

    Back to Top