If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM F1336 - 20
Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
| Format | Pages | Price | ||
 |
9 | $52.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 9 | $52.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
18 | $62.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More F17.62 Standards Related Products Standard References
Abstract
This specification covers the material, dimensional, and mechanical requirements, and associated test methods for fabricated or molded poly(vinyl chloride) (PVC) gasketed sewer fittings manufactured from pipe, or from a combination of pipe and injection molded parts, or from injection molded parts that are suitable for non-pressure drainage of sewage and surface water, as well as applications involving subsurface drainage. The fittings shall adhere to specified values for outside diameter, wall thickness, socket length, and spigot length. When evaluated according to the test procedures provided herein, the fittings shall meet specified requirements for impact strength, pipe stop load support, internal stress, and branch bending. The products shall also undergo referee testing and quality control tests.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers requirements and test methods for fabricated or molded poly(vinyl chloride) (PVC) gasketed sewer fittings to be used with piping manufactured to Specifications D3034, F679, F891 or F1760. Fabricated fittings may be manufactured from pipe, or from a combination of pipe and injection molded parts, or from injection molded parts. Gasketed sewer fitting configurations may include one or more spigot outlets.
1.2 The requirements of this specification are to provide fabricated or molded PVC gasketed fittings suitable for non-pressure drainage of sewage and surface water, as well as applications involving subsurface drainage.
Note 1: Industrial waste lines should be installed only with the specific approval of the governing code authority when using chemicals not commonly found in drains and sewers or temperatures in excess of 140 °F (60 °C), or both.
1.3 Fittings produced to this specification are intended to be installed with pipe, in accordance with Practice D2321.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following precautionary caveat pertains to the test method portion only, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2749 Symbols for Dimensions of Plastic Pipe Fittings
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F610/F610M Practice for Evaluating the Quality of Molded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion Technique
F656 Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
F679 Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
F891 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F1760 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
Military Standard
MIL-STD-129 Marking for Shipment and StorageICS Code
ICS Number Code 23.040.45 (Plastic fittings); 23.040.80 (Seals for pipe and hose assemblies)
UNSPSC Code
UNSPSC Code 40171517(Commercial PVC pipe)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/F1336-20
Citation Format
ASTM F1336-20, Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top