ASTM F1314 - 18

    Standard Specification for Wrought Nitrogen Strengthened 22 Chromium–13 Nickel–5 Manganese–2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910)

    Active Standard ASTM F1314 | Developed by Subcommittee: F04.12

    Book of Standards Volume: 13.01


      Format Pages Price  
    PDF 5 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $55.20   ADD TO CART



    Abstract

    This specification covers the chemical, mechanical, and metallurgical requirements for wrought nitrogen strengthened 22chromium-13nickel-5manganese-2.5molybdenum stainless steel alloy bar and wire for surgical implants (UNS S20910). Materials shall be tested and shall conform to chemical requirements such as chemical composition, and product analysis; metallurgical requirements such as inclusion; and mechanical requirements such as dimension, tensile strength, yield strength, elongation, and Brinell hardness.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the chemical, mechanical, and metallurgical requirements for wrought nitrogen strengthened 22 chromium – 13 nickel – 5 manganese – 2.5 molybdenum stainless steel alloy bar and wire for surgical implants.

    1.2 The SI units in this standard are the primary units. The values stated in either primary SI units or secondary inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values form the two systems may result in non-conformance with the standard.

    1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Aerospace Materials Specification

    AMS 2248

    AMS 2630

    AMS 2632 Ultrasonic Inspection of Thin Materials

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

    A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    E8/E8M Test Methods for Tension Testing of Metallic Materials

    E10 Test Method for Brinell Hardness of Metallic Materials

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E45 Test Methods for Determining the Inclusion Content of Steel

    E112 Test Methods for Determining Average Grain Size

    E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys

    E407 Practice for Microetching Metals and Alloys

    F138 Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Bar and Wire for Surgical Implants (UNS S31673)

    F746 Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials


    ICS Code

    ICS Number Code 11.040.40 (Implants for surgery, prothetics and orthotics)

    UNSPSC Code

    UNSPSC Code 42295500(Surgical implants and expanders and extenders and surgical wires and related products)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F1314-18

    Citation Format

    ASTM F1314-18, Standard Specification for Wrought Nitrogen Strengthened 22 Chromium–13 Nickel–5 Manganese–2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910), ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top