| ||Format||Pages||Price|| |
|8||$46.00||  ADD TO CART|
|Hardcopy (shipping and handling)||8||$46.00||  ADD TO CART|
|Standard + Redline PDF Bundle||16||$55.20||  ADD TO CART|
This specification covers expanded metal. Expanded metal shall be of the following types, classes, grades such as type I-expanded, type II-expanded and flattened, class I-uncoated, class2-hot-dip zinc uncoated, class 3-corrosion resisting steel, grade A and grade B. Expanded metal shall be made from commercial steel, carbon steel sheets or from stainless steel sheets. Expanded metal shall be manufactured with the corresponding thickness, design size, opening size and strand size. Each single strand test specimen shall be visually inspected, and that surface of the strand observed to have the most nearly uniform coating shall be the tension surface when the strand is subject to bending. The coating thickness shall be measured microscopically at a suitable magnification. The minimum and maximum coating thicknesses shall be measured on each of the four exposed surfaces, but not at the corners.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers expanded metal.
1.1.1 Expanded metal covered by this specification is intended for a variety of applications.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only and may be approximate.
1.3 The following precautionary caveat pertains only to the test methods portion, Section This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. , of this specification.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
A700 Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
SAE StandardSAE J1086 Numbering Metals and Alloys (Stabilized October 2012)
Military StandardsMIL-C-16173 Corrosion Preventive Compound, Solvent Cutback, Cold-Application MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes
ICS Number Code 47.020.05 (Materials and components for shipbuilding)
UNSPSC Code 11101704(Steel)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F1267-18, Standard Specification for Metal, Expanded, Steel, ASTM International, West Conshohocken, PA, 2018, www.astm.orgBack to Top