| ||Format||Pages||Price|| |
|10||$50.00||  ADD TO CART|
|Hardcopy (shipping and handling)||10||$50.00||  ADD TO CART|
This specification covers swaged welded, cast, or forged turnbuckles with and without jam nuts. A turnbuckle is an internally threaded loop or sleeve intended for assembly with a threaded stud, eye, hook, or jaw at each end, used for applying tension to rods, wire rope, and so forth. Turnbuckles shall be of the following types and grades: Type I (forged, spread, resistance welded and arc or gas welded); Type II; and Type III. Turnbuckles shall be of the following classes; Class A; Class B; Class C; Class D; Class E; Class F; Class G; and Class H. The following tests shall be performed: proof test; breaking strength test; bending test; and galvanizing test.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers swaged welded, cast, or forged turnbuckles with and without jam nuts.
1.2 A turnbuckle is an internally threaded loop or sleeve intended for assembly with a threaded stud, eye, hook, or jaw at each end, used for applying tension to rods, wire rope, and so forth.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Military SpecificationMIL-L-19140 Lumber and Plywood, Fire-Retardant Treated MIL-P-116
Military StandardsMIL-STD-1186 Cushioning, Anchoring, Bracing, Blocking, and Waterproofing; with Appropriate Test Methods MIL-STD-2073-1
AWS StandardsAWS A5.1 Covered Carbon Steel Arc Welding Electrodes AWS A5.2 Iron and Steel Oxyfuel Gas Welding Rods AWS A5.5
A29/A29M Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel
D3951 Practice for Commercial Packaging
ANSI StandardsANSI B1.1 Unified Inch Screw Threads (UN and UNR Thread Form) ANSI B18.2.2 Square and Hex Nuts
Federal SpecificationsPPP-B-636 Boxes, Shipping, Fiberboard
Federal StandardFED-STD-123 Marking for Shipment (Civil Agencies)
ICS Number Code 21.060.70 (Clamps and staples)
UNSPSC Code 31162405(Turnbuckles)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F1145-05(2017), Standard Specification for Turnbuckles, Swaged, Welded, Forged, ASTM International, West Conshohocken, PA, 2017, www.astm.orgBack to Top