| ||Format||Pages||Price|| |
|4||$44.00||  ADD TO CART|
|Hardcopy (shipping and handling)||4||$44.00||  ADD TO CART|
This specification covers warping heads used with windlass, winch, and capstan drive units to pull rope on board ships. Warping heads are primarily for use with fiber rope, natural, or synthetic. Warping heads with external ribs or whelps on the barrel, notched flanges, attached storage drums, unfinished drums, or non heat-treated fabrications, are considered special. The size of the warping head shall be identified by the nominal barrel diameter measured at the smallest point of the barrel. These warping heads are furnished in two types: Type I is with a cylindrical barrel which is generally used in but not restricted to horizontal shaft applications and Type II is with a conical barrel which is mounted with the large end of the barrel toward the drive machinery. It is generally used in but not restricted to vertical shaft applications. On the other hand, the warping heads are divided into four grades according to composition: Grade 1 is fabricated from any combination of structural steel plate, pipe, tubing, or steel castings and joined by electric welding; Grade 2 is made from mild to medium strength steel; Grade 3 is fabricated from any combination of steel plate or steel castings and joined by electric welding; and Grade 4 is cast from high strength steel castings. Principal dimensions, tolerances, and strength requirements are discussed.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers warping heads used with windlass, winch, and capstan drive units to pull rope on board ships. Warping heads are primarily for use with fiber rope, natural, or synthetic.
1.2 Warping heads with external ribs or whelps on the barrel, notched flanges, attached storage drums, unfinished drums, or non heat-treated fabrications, are considered special and are permitted within the scope of this specification when fully described under special ordering information.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A27/A27M Specification for Steel Castings, Carbon, for General Application
A36/A36M Specification for Carbon Structural Steel
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A148/A148M Specification for Steel Castings, High Strength, for Structural Purposes
A501 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing
A724/A724M Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels
A735/A735M Specification for Pressure Vessel Plates, Low-Carbon Manganese-Molybdenum-Columbium Alloy Steel, for Moderate and Lower Temperature Service
E10 Test Method for Brinell Hardness of Metallic Materials
AWS StandardD1.1 Structural Welding Code
ANSI StandardASA B46.1 Surface Texture
Military StandardsFed-Spec T-R-605 Manila, Three Strand MIL-R-24050
ICS Number Code 47.020.40 (Lifting and cargo handling systems)
UNSPSC Code 25111900(Marine craft systems and subassemblies)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM F1106-87(2018), Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head), ASTM International, West Conshohocken, PA, 2018, www.astm.orgBack to Top