ASTM F1097 - 17

    Standard Specification for Mortar, Refractory (High-Temperature, Air-Setting)

    Active Standard ASTM F1097 | Developed by Subcommittee: F25.07

    Book of Standards Volume: 01.07


      Format Pages Price  
    PDF 5 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $58.00   ADD TO CART



    Abstract

    This specification covers dry air-setting refractory mortar for use in laying and bonding refractory brick in ship boiler furnaces and wet air-setting refractory mortar for use in laying refractory brick in stationary boiler furnaces, bright annealing furnaces, controlled atmosphere furnaces, and furnaces heated by electric elements. The refractory mortar shall be of the following types: Type 1 and Type 2. The mortar shall be composed of finely ground heat-resistant clays, minerals, or a mixture of clays and minerals in either a dry or wet condition. Fineness test, heat soak, and bonding strength test shall be performed to conform with the specified requirements.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers dry air-setting refractory mortar for use in laying and bonding refractory brick in ship boiler furnaces and wet air-setting refractory mortar for use in laying refractory brick in stationary boiler furnaces, bright annealing furnaces, controlled atmosphere furnaces, and furnaces heated by electric elements.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Federal Specifications

    PPP-B-704 Pails: Shipping, Steel (1 through 12 gallon)

    ASTM Standards

    C24 Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High Alumina Refractory Materials

    C27 Classification of Fireclay and High-Alumina Refractory Brick

    C92 Test Methods for Sieve Analysis and Water Content of Refractory Materials

    C133 Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractories

    C198 Test Method for Cold Bonding Strength of Refractory Mortar

    C199 Test Method for Pier Test for Refractory Mortars


    ICS Code

    ICS Number Code 81.080 (Refractories); 91.100.10 (Cement. Gypsum. Lime. Mortar)

    UNSPSC Code

    UNSPSC Code


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/F1097-17

    Citation Format

    ASTM F1097-17, Standard Specification for Mortar, Refractory (High-Temperature, Air-Setting), ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top