ASTM E581 - 17

    Standard Test Methods for Chemical Analysis of Manganese-Copper Alloys

    Active Standard ASTM E581 | Developed by Subcommittee: E01.05

    Book of Standards Volume: 03.05


      Format Pages Price  
    PDF 6 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 12 $55.20   ADD TO CART


    Significance and Use

    4.1 These test methods for the chemical analysis of metals and alloys are primarily intended to test such materials for compliance with compositional specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory.

    1. Scope

    1.1 These test methods cover the chemical analysis of manganese-copper alloys having chemical compositions within the following limits:

    Element

    Range, %

    Copper

    68.0 to 72.0

    Manganese

    28.0 to 32.0

    Carbon

    0.03 max

    Iron

    0.01 max

    Phosphorus

    0.01 max

    Silicon

    0.05 max

    Sulfur

    0.01 max

    1.2 The test methods appear in the following order:

     

    Sections

    Iron by the 1,10-Phenanthroline
     Spectrophotometric Method
     [0.003 % to 0.02 %]

    11 – 20

    Manganese by the (Ethylenedinitrilo)
     Tetraacetic Acid (EDTA)—
     Back-Titrimetric Method [28 % to 32 %]


    21 – 27

    Phosphorus by the
     Molybdivanadophosphoric Acid
     Extraction Spectrophotometric Method
     [0.002 % to 0.014 %]


    28 – 38

    1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D1193 Specification for Reagent Water

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E50 Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials

    E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

    E60 Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry

    E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition

    E135 Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials

    E173 Practice for Conducting Interlaboratory Studies of Methods for Chemical Analysis of Metals

    E1601 Practice for Conducting an Interlaboratory Study to Evaluate the Performance of an Analytical Method


    ICS Code

    ICS Number Code 77.040.30 (Chemical analysis of metals); 77.120.30 (Copper and copper alloys)

    UNSPSC Code

    UNSPSC Code 11172300(Manganese based alloys)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E0581-17

    Citation Format

    ASTM E581-17, Standard Test Methods for Chemical Analysis of Manganese-Copper Alloys, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top