ASTM E3209 - 19

    Standard Test Method for Pavement Thickness by Magnetic Pulse Induction

    Active Standard ASTM E3209 | Developed by Subcommittee: E17.41

    Book of Standards Volume: 04.03


      Format Pages Price  
    PDF 5 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $48.00   ADD TO CART



    Significance and Use

    5.1 This test method covers the indirect measurement of the pavement thickness to provide a rapid, nondestructive result. The method is used to determine the compliance of asphalt or concrete pavement construction with the thickness specifications. The nondestructive thickness results for concrete pavements have shown excellent correlation (R2 values of 99.7 %) with direct measurement of pavement thickness using AASHTO T 148 and Test Method C174/C174M.

    5.2 Measurement results from MPI devices are unaffected by concrete or asphalt material composition, including the use of slag or other metallic aggregates, material temperature, or moisture content, thus allowing installers a quality control process that provides results that can be used in controlling the paving operation. In addition, quantitative results are produced to document as-built thicknesses.

    5.3 Infrastructure owners use the same device to perform quality assurance activities and to accept installed facilities. Its accuracy and repeatability allow the reduction or elimination of coring requirements related to pavement thickness determination.

    1. Scope

    1.1 This test method covers the equipment, field procedures, and interpretation of the results for the pavement thickness measurements produced by a magnetic pulse induction (MPI) device. Magnetic pulse induction devices induce a weak-pulsed magnetic field that causes the induction of eddy currents in metal objects disturbing the field. In order to measure pavement thickness with an MPI device, a pre-placed metal reflector is required. When the metal reflector enters into the field, an electrical signal is produced and processed through algorithms to detect and produce quantitative values for pavement thickness.

    1.2 This test method also provides the details including configuration and metallurgy required to purchase and install reflectors to produce accurate and repeatable results.

    1.3 This method is intended for use with plain-jointed concrete pavements, asphalt pavements, base courses with cement binders, and unbound aggregate layers. It is not applicable for continuously reinforced, mesh-reinforced, or fiber-reinforced pavement where the metal reinforcement would interfere with the magnetic field.

    1.4 MPI equipment includes a device that induces the magnetic field and collects the electrical signal. The signal information is collected and processed into pavement thicknesses through algorithms programmed into the device firmware.

    1.5 MPI field procedures describe the steps and processes required to collect reliable, repeatable, and accurate results from the MPI device. Critical to the accuracy are the metallurgy and configuration of the metal reflectors pre-placed prior to installation of the asphalt or concrete pavement. Also, the absence of any metallic object near the reflector is required to avoid influencing the test result.

    1.6 MPI results require little interpretation when the correct reflector calibration is selected and used during the field test.

    1.7 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

    1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    C174/C174M Test Method for Measuring Thickness of Concrete Elements Using Drilled Concrete Cores

    C802 Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials


    ICS Code

    ICS Number Code 93.080.20 (Road construction materials)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E3209-19

    Citation Format

    ASTM E3209-19, Standard Test Method for Pavement Thickness by Magnetic Pulse Induction, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top