ASTM E3205 - 20

    Standard Test Method for Small Punch Testing of Metallic Materials

    Active Standard ASTM E3205 | Developed by Subcommittee: E10.02

    Book of Standards Volume: 12.02


      Format Pages Price  
    PDF 12 $56.00   ADD TO CART
    Hardcopy (shipping and handling) 12 $56.00   ADD TO CART



    Significance and Use

    4.1 The safety margins provided in the design for a component or structure can be reduced throughout its service life by aging. Aging is the process by which the physical and mechanical characteristics of component or structure materials change with time or use; this process may proceed by a single aging mechanism or a combination of several aging mechanisms.

    4.2 The term “safety margin” is used in a broad sense, meaning the safety state (that is, integrity and functional capability) of components in excess of their normal operational requirements (1).3

    4.3 The determination of mechanical properties such as yield strength, tensile strength, and ductile-to-brittle transition temperature of structural components is, hence, desirable for optimization of operating procedures and inspection intervals, as well as repair strategies and residual lifetime assessment. Current standardized mechanical tests require relatively large volumes of test material that cannot be extracted from in-service equipment without post-sampling removal repair (2).

    4.4 The need to obtain estimates of the mechanical properties of components without post-sampling removal repair has led to the development of small punch (SP) test techniques based on penetration/bulge tests of miniaturized test specimens (often disk-shaped, or square) (3, 4, 5). It can be considered as a quasi-nondestructive technique because of the very limited amount of material to be sampled. It is an efficient and cost-effective technique and has the potential to provide estimates of the material properties of the specific component, identifying the present state of damage and focusing on the most critical (most stressed, most damaged) locations in the component. Examples of empirical correlations that have been established between small punch test results and mechanical properties for specific classes of materials are provided in Appendix X1.

    4.5 This test method can be also used for identifying the most suitable materials with respect to their resistance against operational damage, like neutron irradiation, thermal aging etc., as well as for optimization of their chemical composition, thermal heat treatment, etc. This test method is beneficial in the study of the effect of radiation damage when test specimen dimensions are limited by small irradiation volume or high activity.

    4.6 Due to the small sample size, this test method also allows estimating mechanical properties of non-uniform materials such as welds (6). Examples of weld techniques that produce narrow geometric gradients include electron beam or laser beam welds, and metal coatings (7, 8). This test technique provides a more direct means of estimating material properties than indirect methods based on laboratory simulations of the localized regions or analytical predictions based on generalized methods.

    1. Scope

    1.1 This test method covers procedures for conducting the small punch deformation test for metallic materials. The results can be used to derive estimates of yield and tensile strength up to 450 °C, and estimates of the ductile-to-brittle transition temperature from the results of small punch bulge tests in the temperature range from -193 °C to 350 °C for iron based materials or 0.4 Tm for other metallic materials, where Tm is their melting temperature in K.

    1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    E8/E8M Test Methods for Tension Testing of Metallic Materials

    E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials

    E74 Practices for Calibration and Verification for Force-Measuring Instruments

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E220 Test Method for Calibration of Thermocouples By Comparison Techniques

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E3205-20

    Citation Format

    ASTM E3205-20, Standard Test Method for Small Punch Testing of Metallic Materials, ASTM International, West Conshohocken, PA, 2020, www.astm.org

    Back to Top