ASTM E2377 - 10

    Standard Specification for Shelter, Electrical Equipment, Lightweight

    Active Standard ASTM E2377 | Developed by Subcommittee: E06.53

    Book of Standards Volume: 04.12

      Format Pages Price  
    PDF 11 $52.00   ADD TO CART
    Hardcopy (shipping and handling) 11 $52.00   ADD TO CART
    Standard + Redline PDF Bundle 22 $62.40   ADD TO CART


    This specification covers two types of lightweight electrical equipment shelters designed for transport on both the M1037 and M1097 high mobility multipurpose wheeled vehicle (HMMWV) by rail, air, marine, and highway when mounted or dismounted from their vehicles. The shelters will be of the following types: Type I shelters without tunnel(17-2-0035-1); and Type III modified general-purpose shelters with tunnel (17-2-0035-3). Shelters shall undergo rigid verification procedures to inspect their conformance to requirements pertaining to physical performance, environmental performance, transportability performance, identification, toxicity, and flame resistance.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers two types of lightweight electrical equipment shelters designed for transport on the M1152A1, M1152A1 with B2 Armor Kit, M1037, and M1097 High Mobility Multipurpose Wheeled Vehicle (HMMWV). These shelters are transported by rail, air, marine and highway when mounted or dismounted from their vehicles.

    1.2 ClassificationThe shelters will be of the following types, as specified (see 6.2).

    1.2.1 Type IShelter, Electrical Equipment, Lightweight (w/o Tunnel, 17-2-0035-1).

    1.2.2 Type IIIShelter, Electrical Equipment, Lightweight, Modified, General Purpose (w/ Tunnel, 17-2-0035-3).

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Commercial Standard

    SAE-AS8090 Equipment, Towed Aerospace Ground, Mobility

    Federal Standard

    FED-STD-595 Colors Used in Government Procurement

    Military Standards

    MIL-C-53072 Chemical Agent Resistant Coating (CARC) System Application Procedures and Quality Control Inspection

    Military Handbook

    MIL-HDBK-1791 Designing for Internal Aerial Delivery in Fixed Winged Aircraft

    ACGIH Documents

    Threshold Limit Values


    13228E1639 Standard Camouflage, Pattern For Shelter, Lightweight, Multipurpose

    ASTM Standards

    E1851 Test Method for Electromagnetic Shielding Effectiveness of Durable Rigid Wall Relocatable Structures

    E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures

    ICS Code

    ICS Number Code 29.260.99 (Other electrical equipment for working in special conditions)

    UNSPSC Code

    UNSPSC Code 30162400(Partition walls); 39120000(Electrical equipment and components and supplies)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E2377-10

    Citation Format

    ASTM E2377-10, Standard Specification for Shelter, Electrical Equipment, Lightweight, ASTM International, West Conshohocken, PA, 2010,

    Back to Top