ASTM E1925 - 18

    Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures

    Active Standard ASTM E1925 | Developed by Subcommittee: E06.53

    Book of Standards Volume: 04.11

      Format Pages Price  
    PDF 13 $58.00   ADD TO CART
    Hardcopy (shipping and handling) 13 $58.00   ADD TO CART
    Standard + Redline PDF Bundle 26 $69.00   ADD TO CART


    This specification covers engineering and design criteria for rigid wall relocatable structures (RWRSs) which shall be used for designing expandable and nonexpendable RWRSs. RWRSs shall be manufactured from recovered materials, wherein intimate contact of dissimilar materials shall not be allowed (to prevent galvanic corrosion), all components shall be adequately protected from corrosion, and the materials used shall not cause any skin irritation or injury to the person handling the material during transportation, operation, or maintenance of the equipment. Tests for compatibility, air transportability, ground mobility, rail transportability, forklift handling, erecting and striking, air tightness, blackout, humidity resistance, marine atmosphere, temperature, solar load, temperature shock, heat transfer, blowing sand, sunshine (ultraviolet effects), flame resistance, fungus resistance, squareness, panel flatness, roof loads, floor loads, door loads, panel attachment points, leveling devices, lifting and towing provision strength, tow and dragging simulator, flat and rotational drop (with or without skids), drop shock, impact resistance, electromagnetic interference provisions, water tightness, and lift shall be performed and shall conform to the requirements specified.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers engineering and design criteria required for the development of rigid wall relocatable structures (RWRS) and shall be applied to the design of expandable and nonexpandable RWRSs. This specification applies to present engineering and design requirements for effective RWRSs that are operable in a variety of environments without degradation and are capable of all specified transport modes. This specification shall be applied to the design of expandable and nonexpandable RWRSs. This specification is a conversion of a military standard that was approved by all departments and agencies of the Department of Defense.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 The following safety hazards caveat pertains only to the test required portion, Section 10, of this specification. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Military Standards



    MIL-STD-1472D Notice 3, Human Engineering Design Criteria for Military Systems, Equipment and Facilities



    SAE Standard

    SAE-AS8090 Mobility, Towed Aerospace Ground Equipment, General Requirements for

    ASTM Standards

    E631 Terminology of Building Constructions

    E1749 Terminology Relating to Rigid Wall Relocatable Shelters

    E1851 Test Method for Electromagnetic Shielding Effectiveness of Durable Rigid Wall Relocatable Structures

    G21 Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi

    ISO Standards

    ISO668-1995 Series 1 Freight Containers - Classification, Dimensions and Ratings, 5th Edition

    ICS Code

    ICS Number Code 91.060.10 (Walls. Partitions. Facades)

    UNSPSC Code

    UNSPSC Code 30162400(Partition walls)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E1925-18

    Citation Format

    ASTM E1925-18, Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures, ASTM International, West Conshohocken, PA, 2018,

    Back to Top