If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM E1826 - 20

    Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded

    Active Standard ASTM E1826 | Developed by Subcommittee: E06.53

    Book of Standards Volume: 04.11


      Format Pages Price  
    PDF 5 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $54.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $64.00   ADD TO CART



    Abstract

    This specification covers pigmented, sprayable, low volatile organic compound (VOC) corrosion-inhibiting adhesive primers for use on aluminum alloys that are to be adhesively bonded in the fabrication of panels for tactical or relocatable shelters. When applied to a properly prepared surface of aluminum alloy, the primer imparts corrosion resistance and forms a surface suitable for structural bonding and for coating with shelter paint finishes. The physical properties of uncured liquid polymer, cured film on primed surfaces, and bonded specimens shall conform to the prescribed requirements.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers pigmented, sprayable, low volatile organic compound (VOC) corrosion-inhibiting adhesive primers for use on aluminum alloys that are to be adhesively bonded in the fabrication of panels for tactical shelters. When applied to a properly prepared surface of aluminum alloy, the primer imparts corrosion resistance and forms a surface suitable for structural bonding and for coating with shelter paint finishes.

    1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B117 Practice for Operating Salt Spray (Fog) Apparatus

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    D1002 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)

    D3167 Test Method for Floating Roller Peel Resistance of Adhesives

    E631 Terminology of Building Constructions

    E864 Practice for Surface Preparation of Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels

    E865 Specification for Structural Film Adhesives for Honeycomb Sandwich Panels

    E874 Practice for Adhesive Bonding of Aluminum Facings to Nonmetallic Honeycomb Core for Shelter Panels

    E1749 Terminology Relating to Rigid Wall Relocatable Shelters

    Federal Specifications

    QQ-A-250/11d Aluminum Alloy 6061 T6 Plate and Sheet

    QQ-A-250/8d Aluminum Alloy 5052 H34 Plate and Sheet

    Government Document

    Rule1124 Aerospace Assembly and Component Manufacturing Operations, South Coast Air Quality Management District


    ICS Code

    ICS Number Code 77.120.10 (Aluminium and aluminium alloys)

    UNSPSC Code

    UNSPSC Code 11172000(Aluminum based alloys); 31200000(Adhesives and sealants)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E1826-20

    Citation Format

    ASTM E1826-20, Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded, ASTM International, West Conshohocken, PA, 2020, www.astm.org

    Back to Top