If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM E1575 - 18

    Standard Practice for Pressure Water Cleaning and Cutting

    Active Standard ASTM E1575 | Developed by Subcommittee: E34.10

    Book of Standards Volume: 11.03

      Format Pages Price  
    PDF 10 $52.00   ADD TO CART
    Hardcopy (shipping and handling) 10 $52.00   ADD TO CART
    Standard + Redline PDF Bundle 20 $62.00   ADD TO CART

    Significance and Use

    4.1 This practice is intended to provide guidance on the proper operation of pressure water-jet cleaning and cutting equipment.

    4.2 This practice is also applicable at lower pressures where there is foreseeable risk of injury.

    4.3 This practice is provided to assist persons unfamiliar with the operation of water-jet cleaning and cutting equipment in learning to correctly use the equipment.

    4.4 Correct operation and use of the pressure water-jet cleaning and cutting equipment requires that the operator has familiarized himself with the identification of pressure metal fittings, hoses, guns, and accessories in accordance with the original equipment manufacturer’s specifications, instructions, and programmed instructional material; only then shall hydrojetting begin. Modification of water-jetting equipment shall not be done without prior written approval by the manufacturer of the equipment. Employees shall be instructed in the recognition and avoidance of unsafe conditions as identified/required in 5.18. (Warning—Serious harm or injury may result from the misuse of water-jetting equipment and the use of improper fittings, hoses, or attachments.)

    4.5 The use of pressure water-jet equipment for cutting and cleaning is a rapidly evolving technology. This practice will be periodically reviewed for any required changes at least every five years.

    1. Scope

    1.1 This practice covers the personnel requirements, operator training, operating procedures, and recommended equipment performance/design for the proper operation of all types of pressure water-jet cleaning and cutting equipment as normally used by industries concerned with construction, maintenance, repair, cleaning, cutting, and demolition work.

    1.2 The term “high-pressure water jetting” covers all water jetting, including the use of additives or abrasives at pressures above 100.5 psig (0.69 MPa).

    1.3 Any person required to operate or maintain pressure water-jetting equipment shall have been trained and have demonstrated the ability and knowledge to do so in accordance with the original equipment manufacturer's instructions, specifications, and training programs.

    1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See 3.2.3, 4.4, 5.7.2, 5.11, 5.14, 6.2, 6.7, and Sections 8 and 11 for specific hazards statements.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ANSI/IEEE Standard

    957-1987 IEEE Guide for Cleaning Insulators

    ASTM Standards

    E1542 Terminology Relating to Occupational Health and Safety

    ICS Code

    ICS Number Code 25.100.01 (Cutting tools in general); 25.220.20 (Surface treatment)

    UNSPSC Code

    UNSPSC Code 23101508(Cutting machines); 47121800(Cleaning equipment)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/E1575-18

    Citation Format

    ASTM E1575-18, Standard Practice for Pressure Water Cleaning and Cutting, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top