If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8364 / D8364M - 21

    Standard Specification for Geosynthetic Cementitious Composite Mat (GCCM) Materials

    Active Standard ASTM D8364 / D8364M | Developed by Subcommittee: D35.06

    Book of Standards Volume: 04.13


      Format Pages Price  
    PDF 4 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $48.00   ADD TO CART



    1. Scope

    1.1 This specification covers the requirements and properties for geosynthetic cementitious composite mat materials, or GCCM materials, in various applications. The applications where GCCM materials are utilized shall have different required physical properties, which this standard describes.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C1185 Test Methods for Sampling and Testing Non-Asbestos Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards

    C1353/C1353M Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser

    D4439 Terminology for Geosynthetics

    D4759 Practice for Determining the Specification Conformance of Geosynthetics

    D4885 Test Method for Determining Performance Strength of Geomembranes by the Wide Strip Tensile Method

    D5199 Test Method for Measuring the Nominal Thickness of Geosynthetics

    D5494 Test Method for the Determination of Pyramid Puncture Resistance of Unprotected and Protected Geomembranes

    D5641/D5641M Practice for Geomembrane Seam Evaluation by Vacuum Chamber

    D5820 Practice for Pressurized Air Channel Evaluation of Dual-Seamed Geomembranes

    D5993 Test Method for Measuring Mass per Unit Area of Geosynthetic Clay Liners

    D6768/D6768M Test Method for Tensile Strength of Geosynthetic Clay Liners

    D7177/D7177M Specification for Air Channel Evaluation of Polyvinyl Chloride (PVC) Dual Track Seamed Geomembranes

    D8030/D8030M Practice for Sample Preparation for GCCM

    D8058 Test Method for Determining the Flexural Strength of a Geosynthetic Cementitious Composite Mat (GCCM) Using the Three-Point Bending Test

    D8173 Guide for Site Preparation, Layout, Installation, and Hydration of Geosynthetic Cementitious Composite Mats

    D8329 Test Method for Determination of Water/Cementitious Materials Ratio for Geosynthetic Cementitious Composite Mats (GCCMs) and Measurement of the Compression Strength of the Cementitious Material Contained Within


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8364_D8364M-21

    Citation Format

    ASTM D8364 / D8364M-21, Standard Specification for Geosynthetic Cementitious Composite Mat (GCCM) Materials, ASTM International, West Conshohocken, PA, 2021, www.astm.org

    Back to Top