If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8231 - 19

    Standard Practice for the Use of a Low Voltage Electronic Scanning System for Detecting and Locating Breaches in Roofing and Waterproofing Membranes

    Active Standard ASTM D8231 | Developed by Subcommittee: D08.22

    Book of Standards Volume: 04.04

      Format Pages Price  
    PDF 8 $52.00   ADD TO CART
    Hardcopy (shipping and handling) 8 $52.00   ADD TO CART

    Significance and Use

    4.1 The failure to correct membrane breaches during and after its installation can cause premature failure of the membrane and damage to the structure. Root causes may include design deficiencies, faulty application of the membrane system, product failure, material incompatibility, and damage by other trades. Roof designs incorporating a waterproof membrane under overburden must be tested for breaches before overburden is installed.

    4.2 This practice describes a low voltage (less than 50 V as defined by NFPA 70), dual sweep, scanning method using electronic leak detection to locate breaches in waterproof membranes. The method described includes testing procedures designed to provide a part of the quality assurance of roofing and waterproofing membranes.

    4.3 The methods described in this practice may also be used for forensic testing of existing roofing and waterproofing membranes; however, specific limitations apply that are described later.

    1. Scope

    1.1 This practice describes standard procedures for using an electronic scanning system to locate membrane breaches on both horizontal and vertical surfaces to locate potential leaks in exposed roofing and waterproofing membranes.

    1.2 This practice addresses the need for a detailed technical description of a scanning method and procedures that are used to test and verify the integrity of membranes.

    1.3 This practice is not intended to replace visual or other methods of inspection. It is to be used in conjunction with other methods of roof inspection when specified.

    1.4 This practice requires that the detection and location equipment, procedures, and survey parameters used are calibrated to meet established minimum leak detection sensitivity. The detection sensitivity calibration must be verified on a regular basis using the manufacturer’s procedures to assure maximum confidence in the results.

    1.5 Scanning surveys can be used on membranes installed on roofs, plaza decks, pools, water features, covered reservoirs, and other roofing and waterproofing applications.

    1.6 This practice is applicable for membranes made of electrically insulating materials and is used on certain moderately conductive membranes (see Test Method D4496).

    1.7 This practice provides a description of the scanning method and equipment for locating membrane breaches using electric conductance and is intended to be used in conjunction with the manufacturer’s instructions for the proper operation and use of the equipment.

    1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    NFPA Standards

    NFPA 70 National Electrical Code

    ASTM Standards

    D1079 Terminology Relating to Roofing and Waterproofing

    D4496 Test Method for D-C Resistance or Conductance of Moderately Conductive Materials

    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8231-19

    Citation Format

    ASTM D8231-19, Standard Practice for the Use of a Low Voltage Electronic Scanning System for Detecting and Locating Breaches in Roofing and Waterproofing Membranes, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top