If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8195 - 18

    Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting

    Active Standard ASTM D8195 | Developed by Subcommittee: D20.19

    Book of Standards Volume: 08.03

      Format Pages Price  
    PDF 4 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $48.00   ADD TO CART

    Significance and Use

    4.1 The purpose of this classification system is to provide a method of adequately identifying polyethylene terephthlate films and sheeting and to provide a means for specifying these films and sheeting by the use of a simple line call-out designation.

    1. Scope

    1.1 This standard provides a classification system for tabulating the properties for biaxially oriented polyethylene terephthalate film and sheeting in thicknesses from 1.5 μm to 355 μm. For this classification system, polyethylene terephthalate film and sheeting shall be defined as the material derived from terephthalic acid and ethylene glycol and shall consist of at least 90 % polyethylene terephthalate homopolymer with a typical melting temperature range of 225 °C to 250 °C. This specification does not apply to coated, coextruded, tinted, pigmented, or metallized film or sheeting. This classification (in accordance with D8065/D8065M) is intended to eventually replace Specification D5047 (ref. Note 3).

    Note 1: Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 250 µm.

    Note 2: In order to conform to the original scope of Specification D5047, this classification also includes sheeting up to and including thicknesses of 355 µm.

    Note 3: It is strongly recommended that this classification system be used for all new applications and specifications and that the specification of films referencing Specification D5047 be expeditiously withdrawn or converted to this classification system.

    1.2 Polyethylene terephthalate materials, being thermoplastic, are reprocessable and recyclable. This specification allows for the use of those polyethylene terephthalate plastic materials, provided that any specific requirements as governed by the producer and end user are met.

    1.3 In all cases where the provisions of this classification system would conflict with a currently referenced ASTM specification for a particular film product, the latter shall take precedence (see Note 3).

    1.4 This classification system applies to commercial products and, as such, there is no control over the manufacturing parameters employed in producing the film. It shall be the responsibility of those developing the specification documents utilizing this classification system to identify the critical parameters and values to be used for the cell classifications and suffix requirements.

    1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    Note 4: There is no known ISO equivalent to this standard.

    1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation

    D882 Test Method for Tensile Properties of Thin Plastic Sheeting

    D883 Terminology Relating to Plastics

    D1003 Test Method for Haze and Luminous Transmittance of Transparent Plastics

    D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

    D1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method

    D3892 Practice for Packaging/Packing of Plastics

    D5047 Specification for Polyethylene Terephthalate Film and Sheeting

    D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    ICS Code

    ICS Number Code 83.140.10 (Films and sheets)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8195-18

    Citation Format

    ASTM D8195-18, Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top