If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8194 - 18e1

    Standard Practice for Evaluation of Suitability of 37 mm Filter Monitors and 47 mm Filters Used to Determine Particulate Contaminant in Aviation Turbine Fuels

    Active Standard ASTM D8194 | Developed by Subcommittee: D02.J0.05

    Book of Standards Volume: 05.05

      Format Pages Price  
    PDF 7 $52.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $52.00   ADD TO CART

    Significance and Use

    5.1 This practice provides criteria for products used to measure particulate matter present in a sample of aviation turbine fuel. The objective is to verify that filters, support pads, and field monitors fall within the acceptable ranges that are established by this practice.

    1. Scope

    1.1 This practice determines suitability of products used for measuring particulate contamination in aviation turbine fuel when using Test Methods D5452 and D2276.

    1.2 There are two major parts of this practice. The first is for evaluation of the cellulose acetate butyrate field monitors that are used in combination with the filters and the filter support pads. The second part is for evaluation of the filter when used with an appropriate cellulose acetate butyrate field monitor.

    1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D362 Specification for Industrial Grade Toluene

    D1193 Specification for Reagent Water

    D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption

    D1655 Specification for Aviation Turbine Fuels

    D2276 Test Method for Particulate Contaminant in Aviation Fuel by Line Sampling

    D2624 Test Methods for Electrical Conductivity of Aviation and Distillate Fuels

    D3948 Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer

    D4171 Specification for Fuel System Icing Inhibitors

    D5452 Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration

    F316 Test Methods for Pore Size Characteristics of Membrane Filters by Bubble Point and Mean Flow Pore Test

    Federal Standard

    MIL-DTL-85470 Inhibitor, Icing, Fuel System, High Flash NATO Code Number S-1745 Available from DLA Document Services, Bldg. 4/D, 700 Robbins Ave., Philadelphia, PA 19111-5094, http://quicksearch.dla.miL.

    ICS Code

    ICS Number Code 75.160.20 (Liquid fuels)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8194-18E01

    Citation Format

    ASTM D8194-18e1, Standard Practice for Evaluation of Suitability of 37 mm Filter Monitors and 47 mm Filters Used to Determine Particulate Contaminant in Aviation Turbine Fuels, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top