ASTM D8106 - 17

    Standard Test Methods for Determining the Oil Sorption Capacity of Organophilic Clay

    Active Standard ASTM D8106 | Developed by Subcommittee: D18.21

    Book of Standards Volume: 04.09


      Format Pages Price  
    PDF 5 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $48.00   ADD TO CART



    Significance and Use

    5.1 This standard test method is intended as an index test to determine the relative oil sorption capacity of an organophilic clay. Organophilic clay is used for remediation of contaminated sediment, soil, and groundwater. Results of this standard test method can be used for a) evaluating whether product meets a manufacturing quality control specification, and b) evaluating acceptance of a product per a construction quality assurance material specification. The organophilic clay specified may be either granular or powder. There are two test methods; a gravity test method for granular specimens and a centrifuge test method for powdered specimens.

    Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.

    1. Scope

    1.1 This standard covers two test methods (Method A for granular material, Method B for powdered material) that can be used as an index test for the evaluation of the oil sorption capacity of a representative sample of organophilic clay. The test method is not intended to be a performance test and the oil specified in the test methods may yield different results than other non-aqueous phase liquids (for example, coal tar, creosote, crude oil) encountered in the field. Method A should only be used on granular organophilic clay; otherwise finer particles may pass through the test sieve.

    1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

    1.2.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of the reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

    1.3 Units—The values stated in SI units are to be regarded as the primary units for the standard. For information only, non-SI units of measurement are also included in this standard to describe some equipment (bucket, sieve).

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4753 Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing

    D6026 Practice for Using Significant Digits in Geotechnical Data

    D6913 Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves


    ICS Code

    ICS Number Code 91.100.15 (Mineral materials and products)

    UNSPSC Code

    UNSPSC Code 11111800(Clays)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8106-17

    Citation Format

    ASTM D8106-17, Standard Test Methods for Determining the Oil Sorption Capacity of Organophilic Clay, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top