If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8089 - 17

    Standard Practice for Accelerated Heat Aging for Floor Covering Adhesives

    Active Standard ASTM D8089 | Developed by Subcommittee: D14.10

    Book of Standards Volume: 15.06

      Format Pages Price  
    PDF 3 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $48.00   ADD TO CART

    Significance and Use

    4.1 The final appearance of an installed floor depends upon several factors. These include but are not limited to the manufacture of the flooring material, the preparation of the subfloor and the skill of the installer. This practice is used to measure the ability of the adhesive to retain its original physical properties and adhesion following exposure to heat simulating a long service life at reasonable and expected temperatures.

    4.2 In selecting or developing a carpet or resilient flooring or other adhesive, it is critical to have knowledge regarding how well the adhesive will bond to the substrate and to the flooring material.

    4.3 Heat accelerated aging is necessary to establish the stability of the adhesive as it concerns storage/shelf life including viscosity (Test Method D1084) while remaining in an unopen container for prolonged periods.

    4.4 In determining the applicable physical properties for shear strength (Test Method D6004) and peel strength (Test Method D6862) for the determination of dimensional stability of the assembled flooring material.

    1. Scope

    1.1 This practice describes a procedure to determine the physical properties and longevity of the floor covering adhesive and the effect on it following accelerated heat aging.

    1.2 This practice assists in determining compatibility of adhesive and respective floor covering for long term use.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D123 Terminology Relating to Textiles

    D907 Terminology of Adhesives

    D1084 Test Methods for Viscosity of Adhesives

    D1337 Practice for Storage Life of Adhesives by Viscosity and Bond Strength

    D6004 Test Method for Determining Adhesive Shear Strength of Carpet Adhesives

    D6862 Test Method for 90 Degree Peel Resistance of Adhesives

    D7799 Specification for Tufted and Woven Broadloom Carpet Adhesives Without Homogenous PVC or Non-PVC Backings

    D7888 Practice for Evaluating Adhesive and the Effects of Plasticizer Found Within Polyvinyl Chloride-Backed Floor Coverings

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    F141 Terminology Relating to Resilient Floor Coverings

    F2199 Test Method for Determining Dimensional Stability of Resilient Floor Tile after Exposure to Heat

    ICS Code

    ICS Number Code 83.180 (Adhesives)

    UNSPSC Code

    UNSPSC Code 52100000(Floor coverings); 31200000(Adhesives and sealants)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8089-17

    Citation Format

    ASTM D8089-17, Standard Practice for Accelerated Heat Aging for Floor Covering Adhesives, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top