ASTM D8074 - 18

    Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine

    Active Standard ASTM D8074 | Developed by Subcommittee: D02.B0

    Book of Standards Volume: 05.05


      Format Pages Price  
    PDF 49 $74.00   ADD TO CART
    Hardcopy (shipping and handling) 49 $74.00   ADD TO CART
    Standard + Redline PDF Bundle 98 $88.80   ADD TO CART



    Significance and Use

    5.1 This test method was developed to evaluate the liner scuffing and ring distress performance of engine oils in turbocharged and intercooled four-cycle diesel engines equipped with EGR, uncoated top rings, and running on ultra-low sulfur diesel fuel. Results are obtained from used oil analysis, operational data, and component measurements before and after test.

    5.2 The test method may be used for engine oil specification acceptance when all details of the procedure are followed.

    1. Scope

    1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including adhesive wear between an uncoated piston ring and cylinder liner. This test method is commonly referred to as the DD13 Scuffing Test.

    1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.2.1 Exception—Where there is no direct SI equivalent, such as the units for screw threads, National Pipe Threads/diameters, tubing size, and single source supply equipment specifications.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A2 for specific safety precautions.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure

    D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

    D97 Test Method for Pour Point of Petroleum Products

    D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

    D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)

    D287 Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)

    D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

    D482 Test Method for Ash from Petroleum Products

    D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products

    D613 Test Method for Cetane Number of Diesel Fuel Oil

    D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration

    D975 Specification for Diesel Fuel Oils

    D976 Test Method for Calculated Cetane Index of Distillate Fuels

    D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption

    D2274 Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)

    D2500 Test Method for Cloud Point of Petroleum Products and Liquid Fuels

    D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry

    D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge

    D3338 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels

    D3524 Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography

    D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter

    D4175 Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants

    D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry

    D4683 Test Method for Measuring Viscosity of New and Used Engine Oils at High Shear Rate and High Temperature by Tapered Bearing Simulator Viscometer at 150C

    D4739 Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration

    D5185 Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)

    D5186 Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography

    D5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence

    D5967 Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

    D6078 Test Method for Evaluating Lubricity of Diesel Fuels by the Scuffing Load Ball-on-Cylinder Lubricity Evaluator (SLBOCLE)

    D6984 Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine

    D7320 Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E168 Practices for General Techniques of Infrared Quantitative Analysis

    Other Standards

    Code of Federal Regulations Title 40 Part 86.310-79, Available from U.S. Government Printing Office, Superintendent of Documents, 732 N. Capitol St., NW, Washington, DC 20401-0001, http://www.access.gpo.gov. https://www.gpo.gov/fdsys/granule/CFR-2013-title40-vol19/CFR-2013-title40-vol19-sec86-310-79.


    ICS Code

    ICS Number Code 75.100 (Lubricants, industrial oils and related products)

    UNSPSC Code

    UNSPSC Code 26101504(Diesel engines); 15121501(Engine oil)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8074-18

    Citation Format

    ASTM D8074-18, Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top