If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8068 - 19

    Standard Practice for Collection of Culturable Airborne Fungi or Bacteria on Agar Plates by Inertial Impaction Systems

    Active Standard ASTM D8068 | Developed by Subcommittee: D22.08

    Book of Standards Volume: 11.07

      Format Pages Price  
    PDF 4 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 8 $54.00   ADD TO CART

    Significance and Use

    4.1 This practice is intended for the collection of airborne particles on agar plates using inertial impaction for the purpose of culturing fungi or bacteria.

    4.2 This practice is valuable when species level identification or quantity of culturable aerosolized fungi and bacteria are important factors for the indoor air quality investigation.

    4.3 It is the responsibility of the user to assure that they are in compliance with all local, state, and federal regulations governing the inspection of buildings for fungal and bacterial colonization and the collection of associated samples.

    4.4 This practice is intended to provide the user with a basic understanding of the equipment, materials, and instructions necessary to effectively collect air samples on agar plates using an inertial impactor.

    4.5 This practice is intended to minimize systematic sampling variations between different data sets.

    1. Scope

    1.1 The purpose of this practice is to describe procedures for the collection of culturable airborne fungal spores or fragments or bacteria on agar plates using inertial impaction sampling techniques.

    1.2 This practice does not include collection of culturable fungi or bacteria by devices not using agar plates.

    1.3 This practice presumes that the user has a fundamental understanding of field investigative techniques related to the scientific process, and sampling plan development and implementation. It is important to establish the related hypothesis to be tested and the supporting analytical methodology needed in order to identify the sampling media to be used and the laboratory conditions for analysis.

    1.4 This practice does not address the development of a formal hypothesis or the establishment of appropriate and defensible investigation and sampling objectives. It is presumed the investigator has the experience and knowledge base to address these issues.

    1.5 This practice does not provide the user sufficient information to allow for interpretation of the analytical results from sample collection. It is the user's responsibility to seek or obtain the information and knowledge necessary to interpret the sample results reported by the laboratory.

    1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D1356 Terminology Relating to Sampling and Analysis of Atmospheres

    D3195/D3195M Practice for Rotameter Calibration

    D6044 Guide for Representative Sampling for Management of Waste and Contaminated Media

    F1671 Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System

    ICS Code

    ICS Number Code 07.100.99 (Other standards related to microbiology)

    UNSPSC Code

    UNSPSC Code

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8068-19

    Citation Format

    ASTM D8068-19, Standard Practice for Collection of Culturable Airborne Fungi or Bacteria on Agar Plates by Inertial Impaction Systems, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top