If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8024 - 16

    Standard Test Method for Determination of (Tri-n-butyl)-n-tetradecylphosphonium chloride (TTPC) in Water by Multiple Reaction Monitoring Liquid Chromatography/Mass Spectrometry (LC/MS/MS)

    Active Standard ASTM D8024 | Developed by Subcommittee: D19.06

    Book of Standards Volume: 11.02

      Format Pages Price  
    PDF 10 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 10 $54.00   ADD TO CART

    Significance and Use

    5.1 TTPC may be used in various industrial and commercial products for use as a biocide. Products containing TTPC have been approved for controlling algal, bacterial, and fungal slimes in industrial water systems.2 TTPC should not be persistent in water but may be deposited in sediments at concentrations of concern. Hence, there is a need for quick, easy and robust method to determine TTPC concentration at trace levels in water matrices for understanding the sources and concentration levels in affected areas.

    5.2 This method has been used to determine TTPC in reagent water and a river water (Table 8).

    (A) Solution A: Level 8 stock solution prepared according to Section 12 and at Table 4 concentrations.
    (B) Solution B: 75 % Acetone, 25 % Water.

    Note 1: This test method has been used to characterize TTPC in real world water samples with success and similar recoveries as shown in Table 8.

    1. Scope

    1.1 This test method covers the determination of (Tri-n-butyl)-n-tetradecylphosphonium chloride (TTPC) in water by dilution with acetone, filtration and analysis by liquid chromatography/tandem mass spectrometry. This test method is not amenable for the analysis of isomeric mixtures of Tributyl-tetradecylphosphonium chloride. TTPC is a biocide that strongly adsorbs to soils.2 The water samples are prepared in a solution of 75 % acetone and 25 % water because TTPC has an affinity for surfaces and particles. The reporting range for this method is from 100–4000 ng/L. This analyte is qualitatively and quantitatively determined by this method. This test method adheres to multiple reaction monitoring (MRM) mass spectrometry.

    1.2 A full collaborative study to meet the requirements of Practice D2777 has not been completed. This test method contains single-operator precision and bias based on single-operator data. Publication of standards that have not been fully validated is done to make the current technology accessible to users of standards, and to solicit additional input from the user community.

    1.3 The Method Detection Limit3 (MDL) and Reporting Range4 for the target analyte are listed in Table 1.

    1.3.1 The reporting limit in this test method is the minimum value below which data are documented as non-detects. Analyte detections between the method detection limit and the reporting limit are estimated concentrations and are not reported following this test method. The reporting limit is calculated from the concentration of the Level 1 calibration standard as shown in Table 4 for TTPC after taking into account a 2.5 mL water sample volume and a final diluted sample volume of 10 mL (75 % acetone/25 % water). The final solution volume is 10 mL because a 7.5 mL volume of acetone is added to each 2.5 mL water sample which is shaken and filtered.

    1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D1129 Terminology Relating to Water

    D1193 Specification for Reagent Water

    D2777 Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water

    D3856 Guide for Management Systems in Laboratories Engaged in Analysis of Water

    D4841 Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents

    D5847 Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis

    E2554 Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques

    ICS Code

    ICS Number Code 13.060.50 (Examination of water for chemical substances)

    UNSPSC Code

    UNSPSC Code 10191500(Pesticides or pest repellents)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8024-16

    Citation Format

    ASTM D8024-16, Standard Test Method for Determination of (Tri-n-butyl)-n-tetradecylphosphonium chloride (TTPC) in Water by Multiple Reaction Monitoring Liquid Chromatography/Mass Spectrometry (LC/MS/MS), ASTM International, West Conshohocken, PA, 2016, www.astm.org

    Back to Top