If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D8012 - 18

    Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications

    Active Standard ASTM D8012 | Developed by Subcommittee: D18.14

    Book of Standards Volume: 04.09

      Format Pages Price  
    PDF 4 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $48.00   ADD TO CART

    Significance and Use

    4.1 Use of reclaimed asphalt shingles in asphalt production has become commonplace in transportation applications.

    4.2 Use of reclaimed asphalt shingles in unbound applications, such as granular fill, alone or in mixtures with other materials, is developing.

    4.3 The quality of RAS is critical for successful reuse of the shingles in asphalt production and other unbound applications. Various specifications are used regarding RAS.

    4.4 This practice provides a common baseline framework for assuring material, operator, and facility quality for RAS production.

    4.5 This practice provides sourcing, inspecting, sampling, testing, and stockpiling requirements for RAS operators.

    4.6 This practice includes a certification form that is used for quality control and quality assurance for the facility, operations, and incoming material and outgoing product.

    1. Scope

    1.1 This practice covers reclamation of asphalt shingles derived from manufacturing scrap and tear-off roofing. Reclaimed asphalt shingles (RAS) are used in roadway and other applications including asphalt paving materials and unbound materials such as granular fill.

    1.2 Guidance is provided relating to material quality, material quality control, and also operator and facility qualifications.

    1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.

    Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.

    1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

    D75/D75M Practice for Sampling Aggregates

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

    EPA Standard

    EPA 600-R-93-116 Polarized Light Microscopy: Method for the Determination of Asbestos in Bulk Building Materials

    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D8012-18

    Citation Format

    ASTM D8012-18, Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top