If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D7774 - 17

    Standard Test Method for Flexural Fatigue Properties of Plastics

    Active Standard ASTM D7774 | Developed by Subcommittee: D20.10

    Book of Standards Volume: 08.03

      Format Pages Price  
    PDF 6 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $54.00   ADD TO CART
    Standard + Redline PDF Bundle 12 $64.00   ADD TO CART

    Significance and Use

    5.1 These fatigue tests are used to determine the effect of processing, surface condition, stress, and so forth, on the fatigue resistance of plastic material subjected to flexural stress for relatively large numbers of cycles. The results can also be used as a guide for the selection of plastic materials for service under conditions of repeated flexural stress.

    5.2 Properties can vary with specimen depth and test frequency. Test frequency can be 1-25 Hz but it is recommended that a frequency of 5 Hz or less be used.

    5.3 Material response in fatigue is not identical for all plastics. If a plastic does not exhibit an elastic region, where strain is reversible, plastic deformation will occur during fatigue testing, causing the amplitude of the programmed load or deformation to change during testing. In this situation, caution shall be taken when using the results for design as they are generally not indicative of the true fatigue properties of the material.

    5.4 The results of these fatigue tests are suitable for application in design only when the specimen test conditions realistically simulate service conditions or some methodology of accounting for service conditions is available and clearly defined.

    5.5 This procedure accommodates various specimen preparation techniques. Comparison of results obtained from specimens prepared in different manners shall not be considered comparable unless equivalency has been demonstrated.

    1. Scope

    1.1 This test method covers the determination of dynamic full reversed fatigue properties of plastics in flexure. This method is applicable to rigid and semi-rigid plastics. Stress and strain levels are below the proportional limit of the material where the strains and stresses are relatively elastic. Three-point or four-point bending systems are used to determine these properties.

    1.2 This test method can be used with two procedures:

    1.2.1 Procedure A, designed for materials that use three-point loading systems to determine flexural strength. Three-point loading system is used for this procedure.

    1.2.2 Procedure B, designed for materials that use four-point loading systems to determine flexural strength. Four-point loading system is used for this procedure.

    1.3 Comparative tests can be run in accordance with either procedure, provided that the procedure is found satisfactory for the material being tested.

    1.4 The values stated in SI units are to be regarded as the standard. The values provided in parentheses are for information only.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1: This standard and ISO 13003 address the same subject matter, but differ in technical content and results cannot be directly compared between the two test methods.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

    D883 Terminology Relating to Plastics

    D1505 Test Method for Density of Plastics by the Density-Gradient Technique

    D2839 Practice for Use of a Melt Index Strand for Determining Density of Polyethylene

    D3479/D3479M Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials

    D4883 Test Method for Density of Polyethylene by the Ultrasound Technique

    D5947 Test Methods for Physical Dimensions of Solid Plastics Specimens

    D6272 Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending

    E4 Practices for Force Verification of Testing Machines

    E83 Practice for Verification and Classification of Extensometer Systems

    E1942 Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing

    ICS Code

    ICS Number Code 83.080.01 (Plastics in general)

    UNSPSC Code

    UNSPSC Code

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D7774-17

    Citation Format

    ASTM D7774-17, Standard Test Method for Flexural Fatigue Properties of Plastics, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top