| ||Format||Pages||Price|| |
|2||$44.00||  ADD TO CART|
|Hardcopy (shipping and handling)||2||$44.00||  ADD TO CART|
This specification covers the properties and requirements for isopropyl alcohol. Specimens shall be suitably sampled and tested, and shall adhere accordingly to specified values of the following properties: apparent specific gravity; color (Pt-Co scale); distillation range; nonvolatile matter content; odor; water content; acidity (acetic acid); and water miscibility.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers isopropyl alcohol (99 % grade).
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice .
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D268 Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material
D1078 Test Method for Distillation Range of Volatile Organic Liquids
D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
D1296 Test Method for Odor of Volatile Solvents and Diluents
D1353 Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products
D1364 Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method)
D1476 Test Method for Heptane Miscibility of Lacquer Solvents
D1613 Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products
D1722 Test Method for Water Miscibility of Water-Soluble Solvents
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E300 Practice for Sampling Industrial Chemicals
U.S. Federal SpecificationPPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging of Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
ICS Number Code 71.080.60 (Alcohols. Ethers)
UNSPSC Code 12352121(Organic hydroxides)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D770-11(2019), Standard Specification for Isopropyl Alcohol,, ASTM International, West Conshohocken, PA, 2019, www.astm.orgBack to Top