ASTM D7055 - 14
Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings
| Format | Pages | Price | ||
 |
3 | $42.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 3 | $42.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
6 | $50.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More D01.46 Standards Related Products Standard References
Significance and Use
4.1 The procedures described in this practice are designed to provide hot-rolled, carbon steel panels with uniform and reproducible abrasive blast cleaned surfaces for testing of coatings.
1. Scope
1.1 This practice covers the procedures to be followed in the preparation (by abrasive blast cleaning) of hot rolled steel panels for laboratory testing of coatings.
1.2 This standard practice does not include procedures for the application of coatings.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A36/A36M Specification for Carbon Structural Steel
A572/A572M Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
D4285 Test Method for Indicating Oil or Water in Compressed Air
D4417 Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
D4940 Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blasting Abrasives
D7393 Practice for Indicating Oil in Abrasives
ISO Standard
ISO 8502-3, Part 3 Assessment of Dust on Steel Surfaces Prepared for Painting (pressure-sensitive tape method) Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.SSPC/NACE Standards
AB-1 Mineral and Slag Abrasives AB-2 Specification for Cleanliness of Recycled Ferrous Metallic Abrasives AB-3 Newly Manufactured or Re-Manufactured Steel Abrasives SP 10/NACE No. 2 Near-White Metal Blast Cleaning SP 1 Solvent Cleaning SP 5/NACE No. 1 White Metal Blast Cleaning SP 6/NACE No. 3 Commercial Blast Cleaning SSPC-VIS 1 Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast CleaningICS Code
ICS Number Code 77.140.50 (Flat steel products and semi-products)
UNSPSC Code
UNSPSC Code 11101704(Steel)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D7055-14
Citation Format
ASTM D7055-14, Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings, ASTM International, West Conshohocken, PA, 2014, www.astm.org
Back to Top