| Format | Pages | Price |   |
![]() |
5 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 5 | $52.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
10 | $62.00 | ![]() |
Historical Version(s) - view previous versions of standard
More D20.15 Standards Related Products Standard References
Abstract
This specification covers acrylonitrile-styrene-acrylate (ASA) and acrylonitrile-EPDM-styrene (AES) plastics and alloys suitable for injection molding and extrusion. ASA and AES materials, and ASA and AES alloys are classified into groups according to their composition. These groups are subdivided into classes and grades: class 0, 1, 2, and 3; grade 0, 1, 2, 3, 4, and 5. The tensile stresses at yield, modulus of elasticity in tension, charpy impact strength, vicat softening temperature, and melt volume-flow rate shall be tested to meet the requirements prescribed.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This classification system covers ASA and AES materials, and ASA and AES alloys suitable for injection molding and extrusion. This classification system does not cover recycled ASA and AES materials, and recycled ASA and AES alloys.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
Note 1: This classification system and ISO 6402 and ISO 19065 address the same subject matter but differ in technical content.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Specifying Plastic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ICS Code
ICS Number Code 83.080.20 (Thermoplastic materials)
UNSPSC Code
UNSPSC Code 13102006(Acrylonitrile Styrene Acrylic ASA alloys)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D6865-17
Citation Format
ASTM D6865-17, Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials, ASTM International, West Conshohocken, PA, 2017, www.astm.org
Back to Top