ASTM D6622 / D6622M - 01(2018)e1

    Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems

    Active Standard ASTM D6622 / D6622M | Developed by Subcommittee: D08.22

    Book of Standards Volume: 04.04


      Format Pages Price  
    PDF 4 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $42.00   ADD TO CART



    Significance and Use

    5.1 This guide outlines general procedures and precautions for the application of fully adhered hot-applied built-up reinforced waterproofing systems.

    5.2 This guide is not all inclusive and is intended only to supplement detailed instructions from designers, and the recommendations of manufacturers. Manufacturers of some of the systems addressed by this guide require proprietary products and special procedures not described in this guide. Manufacturers' recommendations should therefore be considered in the application of this guide.

    5.3 For design guidelines, consult Guide C981.

    1. Scope

    1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces.

    1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C981 Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks

    D41/D41M Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing

    D43/D43M Specification for Coal Tar Primer Used in Roofing, Dampproofing, and Waterproofing

    D173/D173M Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

    D226/D226M Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

    D227/D227M Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

    D449/D449M Specification for Asphalt Used in Dampproofing and Waterproofing

    D450/D450M Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

    D1079 Terminology Relating to Roofing and Waterproofing

    D1327/D1327M Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing

    D1668/D1668M Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing

    D2178/D2178M Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

    D2822/D2822M Specification for Asphalt Roof Cement, Asbestos-Containing

    D4022/D4022M Specification for Coal Tar Roof Cement, Asbestos Containing

    D4586/D4586M Specification for Asphalt Roof Cement, Asbestos-Free

    D4990 Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

    D5295 Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems

    D5643/D5643M Specification for Coal Tar Roof Cement, Asbestos Free

    D5726 Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing

    D5898/D5898M Guide for Standard Details for Adhered Sheet Waterproofing

    D5957 Guide for Flood Testing Horizontal Waterproofing Installations

    D6152/D6152M Specification for SEBS-Modified Mopping Asphalt Used in Roofing

    D6162/D6162M Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

    D6163/D6163M Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

    D6164/D6164M Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

    D6451/D6451M Guide for Application of Asphalt Based Protection Board

    D6506/D6506M Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

    Other Documents

    CAN/CGSB-37.50 Hot-Applied, Rubberized Asphalt for Roofing and Waterproofing Canadian General Standards Board, Ottawa, Canada K1A 1G6.


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D6622_D6622M-01R18E01

    Citation Format

    ASTM D6622 / D6622M-01(2018)e1, Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top