ASTM D6380 / D6380M - 03(2018)

    Standard Specification for Asphalt Roll Roofing (Organic Felt)

    Active Standard ASTM D6380 / D6380M | Developed by Subcommittee: D08.02

    Book of Standards Volume: 04.04


      Format Pages Price  
    PDF 4 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $42.00   ADD TO CART



    Abstract

    This specification covers three classes and three types of asphalt roll roofing in sheet form, in widths agreed upon between the purchaser and the producer/supplier, and composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M and WS rolls are surfaced on the weather (exposed) side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica, or other fine mineral matter to prevent sticking. Type classifications (Types II, III, and IV) are grouped based on minimum net mass per unit area of roofing. Roofing shall adhere to physical property requirements such as breaking strength, water permeance and vapor transmission, width, selvage, area, and moisture.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers asphalt roofing in sheet form, in widths agreed upon between the purchaser and the producer/supplier, composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M and WS rolls are surfaced on the (exposed) weather side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica, or other fine mineral matter to prevent sticking.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D146/D146M Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing

    D224 Specification for Smooth-Surfaced Asphalt Roll Roofing (Organic Felt)

    D228/D228M Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing

    D249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules

    D371 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules; Wide Selvage

    D1079 Terminology Relating to Roofing and Waterproofing

    D3019/D3019M Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, and Fibered

    D4977/D4977M Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

    E96/E96M Test Methods for Water Vapor Transmission of Materials


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30121601(Asphalt); 30151501(Roll roofing)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D6380_D6380M-03R18

    Citation Format

    ASTM D6380 / D6380M-03(2018), Standard Specification for Asphalt Roll Roofing (Organic Felt), ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top