If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D564 - 87(2017)

    Standard Test Methods for Liquid Paint Driers

    Active Standard ASTM D564 | Developed by Subcommittee: D01.21

    Book of Standards Volume: 06.01

      Format Pages Price  
    PDF 3 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $48.00   ADD TO CART

    Significance and Use

    3.1 Driers accelerate the drying of oil, paint, printing ink, and varnish.

    3.2 These test methods are applicable to liquid driers manufactured for use in paints and related coatings.

    3.3 The tests for metallic content using ethylenediaminetetraacetic acid dihydrate (EDTA) are intended for concentrated solutions of single metals; two or more metals may cause interference.

    1. Scope

    1.1 These test methods cover the test procedures to be applied to liquid paint driers used in paints and related coatings. Typical paint driers, listed in Specification D600, are carboxylates of lead, cobalt, manganese, zinc, iron, calcium, and zirconium.

    1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D234 Specification for Raw Linseed Oil

    D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)

    D600 Specification for Liquid Paint Driers

    D1544 Test Method for Color of Transparent Liquids (Gardner Color Scale)

    D1640 Test Methods for Drying, Curing, or Film Formation of Organic Coatings

    D1644 Test Methods for Nonvolatile Content of Varnishes

    D2090 Test Method for Clarity and Cleanness of Paint and Ink Liquids

    D2373 Test Method for Determination of Cobalt in Paint Driers by EDTA Method

    D2374 Test Method for Lead in Paint Driers by EDTA Method

    D2375 Test Method for Manganese in Paint Driers by EDTA Method

    D2613 Test Method for Calcium or Zinc in Paint Driers by EDTA Method

    D3804 Test Method for Iron in Paint Driers by EDTA Method

    D3924 Specification for Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials

    D3969 Test Method for Zirconium in Paint Driers by EDTA Method

    D3970 Test Method for Cerium in Paint Driers by Oxidimetric Determination

    D3980 Practice for Interlaboratory Testing of Paint and Related Materials

    D3988 Test Method for Vanadium in Paint Driers by EDTA Method

    D3989 Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method

    ICS Code

    ICS Number Code 87.060.99 (Other paint ingredients)

    UNSPSC Code

    UNSPSC Code 31211603(Paint driers)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D0564-87R17

    Citation Format

    ASTM D564-87(2017), Standard Test Methods for Liquid Paint Driers, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top