If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D5499 - 94(2021)

    Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems

    Active Standard ASTM D5499 | Developed by Subcommittee: D33.09

    Book of Standards Volume: 06.02

      Format Pages Price  
    PDF 3 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $48.00   ADD TO CART

    Significance and Use

    3.1 The results obtained by these test methods can be used in combination with other test methods for the selection of a lining in flue gas desulfurization (FGD) systems.

    3.2 These methods are intended to evaluate effects of heat alone upon a lining system as applied to a carbon steel substrate. These methods do not produce the thermal gradient that may exist in actual applications. Actual lining performance may also be effected by concurrent physical mechanical or chemical effects.

    3.3 These methods evaluate major failure modes of linings applied to square test panels.

    3.4 The recommended test temperatures of 200°F (93°C) and 350°F (177°C) are based on typical maximum operating zone temperatures in flue gas desulfurizations systems. Other temperatures may be evaluated as desired.

    1. Scope

    1.1 These test methods are intended to evaluate the resistance of polymer linings applied to carbon steel substrates to elevated temperatures. Two separate methods are included as follows:

    1.1.1 Test Method A Continuous elevated temperature exposure, and

    1.1.2 Test Method B Cycling elevated temperature exposure.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A36/A36M Specification for Carbon Structural Steel

    D660 Test Method for Evaluating Degree of Checking of Exterior Paints

    D661 Test Method for Evaluating Degree of Cracking of Exterior Paints

    D714 Test Method for Evaluating Degree of Blistering of Paints

    D772 Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints

    D1474 Test Methods for Indentation Hardness of Organic Coatings

    D4417 Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel

    D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers

    Steel Structures Painting Council Standards (SSPC)

    SSPC No. SP5 Blast Cleaning to White Metal

    ICS Code

    ICS Number Code 83.080.20 (Thermoplastic materials)

    UNSPSC Code

    UNSPSC Code 40161607(Flue gas desulphurization system)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D5499-94R21

    Citation Format

    ASTM D5499-94(2021), Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems, ASTM International, West Conshohocken, PA, 2021, www.astm.org

    Back to Top