| ||Format||Pages||Price|| |
|2||$42.00||  ADD TO CART|
|Hardcopy (shipping and handling)||2||$42.00||  ADD TO CART|
|Standard + Redline PDF Bundle||4||$50.00||  ADD TO CART|
This specification covers benzene-545. Tests shall be performed to determine the property requirements of benzene-545 in accordance to the following test methods: benzene weight percentage; sulfur mass; thiophene mass; toluene mass; nonaromatic hydrocarbons weight percentage; nitrogen mass; acid wash color; bromine index, water, appearance, and solidification point.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers benzene-545.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit in accordance with the rounding-off method in Practice .
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D848 Test Method for Acid Wash Color of Industrial Aromatic Hydrocarbons
D852 Test Method for Solidification Point of Benzene
D1492 Test Method for Bromine Index of Aromatic Hydrocarbons by Coulometric Titration
D3437 Practice for Sampling and Handling Liquid Cyclic Products
D4492 Test Method for Analysis of Benzene by Gas Chromatography
D4735 Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
D5776 Test Method for Bromine Index of Aromatic Hydrocarbons by Electrometric Titration
D6875 Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor
D7011 Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective Detection
D7183 Test Method for Determination of Total Sulfur in Aromatic Hydrocarbons and Related Chemicals by Ultraviolet Fluorescence
D7184 Test Method for Ultra Low Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence Detection
D7360 Test Method for Analysis of Benzene by Gas Chromatography with External Calibration
D7504 Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and Effective Carbon Number
D8005 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E1064 Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration
E2680 Test Method for Appearance of Clear, Transparent Liquids (Visual Inspection Procedure)
ICS Number Code 87.060.30 (Solvents)
UNSPSC Code 15101507(Benzene)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D4734-18a, Standard Specification for Refined Benzene-545, ASTM International, West Conshohocken, PA, 2018, www.astm.orgBack to Top