| Format | Pages | Price |   |
![]() |
5 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 5 | $52.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
10 | $62.00 | ![]() |
Historical Version(s) - view previous versions of standard
More D20.15 Standards Related Products Standard References
Abstract
This specification covers styrene-maleic anhydride materials suitable for molding and extrusion. It does not however apply to alloys or blends of styrene-maleic anhydride materials with non-elastomeric thermoplastics. The materials shall be conditioned and tested for physical and mechanical properties in the standard laboratory atmosphere. Test specimens and testing parameters for the unreinforced and reinforced, filled, or lubricated materials shall conform to the tensile strength, flexural modulus, Izod impact strength, Vicat softening point, and heat deflection temperature requirements.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This classification system covers styrene-maleic anhydride materials suitable for molding or extrusion. This classification system does not apply to alloys or blends of styrene-maleic anhydride materials with non-elastomeric thermoplastics. Styrene-maleic anhydride materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those materials provided that all the specific requirements of this classification system are met.
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5.
1.3 This classification system and subsequent line call out (specification) are intended to provide means of calling out properties of plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Materials should be selected by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, costs involved, and the inherent properties of the material other than those covered by this classification system.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Military Standard
MIL-STD-1916 DOD Preferred Methods for Acceptance of ProductASTM Standards
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883 Terminology Relating to Plastics
D1525 Test Method for Vicat Softening Temperature of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3641 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Specifying Plastic Materials
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ICS Code
ICS Number Code 83.080.20 (Thermoplastic materials)
UNSPSC Code
UNSPSC Code 13111054(Styrene maleic anhydride)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D4634-16
Citation Format
ASTM D4634-16, Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA), ASTM International, West Conshohocken, PA, 2016, www.astm.org
Back to Top