| Format | Pages | Price |   |
![]() |
4 | $46.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 4 | $46.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
8 | $54.00 | ![]() |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More D13.61 Standards Related Products Standard References
Significance and Use
5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4114 except for the following characteristic(s).”
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified test methods.
1. Scope
1.1 This performance specification covers woven flat fabrics comprised of any textile fiber or mixture of fibers to be used as linings for women's and girls' apparel.
1.2 This performance specification is not applicable to woven pile, woven fusible, fire-bonded fusible, sliver-knit pile, and sheepskin lining fabrics.
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.
1.4 The following precautionary statement pertains only to the test methods portion, Section 7, of this performance specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D123 Terminology Relating to Textiles
D434 Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam
D1336 Test Method for Distortion of Yarn in Woven Fabrics
D1424 Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
D2261 Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)
D2724 Test Method for Bond Strength of Bonded, Fused, and Laminated Apparel Fabrics
D5034 Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
D7022 Terminology Relating to Apparel
ICS Code
ICS Number Code 59.080.30 (Textile fabrics)
UNSPSC Code
UNSPSC Code 53100000(Clothing)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D4114-21
Citation Format
ASTM D4114-21, Standard Performance Specification for Woven Flat Lining Fabrics for Women's and Girls' Apparel, ASTM International, West Conshohocken, PA, 2021, www.astm.org
Back to Top