You are being redirected because this document is part of your ASTM Compass® subscription.
    This document is part of your ASTM Compass® subscription.

    ASTM D3309-96a(2002)

    Standard Specification for Polybutylene (PB) Plastic Hot- and Cold-Water Distribution Systems (Withdrawn 2010)

    Withdrawn Standard: ASTM D3309-96a(2002) | Developed by Subcommittee: F17.61

      Format Pages Price  
    PDF 11 $67.00   ADD TO CART

    1. Scope

    1.1 This specification covers requirements, test methods, and methods of marking for polybutylene plastic system components made in one standard dimension ratio and intended for 0.69 MPa (100 psi) water service up to and including 82°C (180°F). These components comprise pipe and tubing, socket-fusion fittings, compression fittings, mechanical fittings, and plastic-to-metal transition fittings. Requirements and test methods are included for sustained, hydrostatic pressure strength, thermocycling resistance, joint strength, and dimensions and tolerances for pipe and socket fusion fittings. The components covered by this specification are intended for use in hot- and cold-water potable water service and distribution systems and such non-potable water applications as building services piping, water heating and cooling systems, fire sprinkler applications, and other miscellaneous applications involving the transport of water, ethylene glycol solutions, or other aqueous liquids shown not to adversely affect PB performance.

    1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

    1.3 The values in SI units are the standard. The values stated in parentheses are for information only.

    Note 1—Suggested hydrostatic design stresses and hydrostatic pressure ratings for pipe, tubing, and fittings are listed in Appendix X1. Design, assembly, and installation considerations are discussed in . An optional performance qualification and an in-plant quality control program are recommended in Appendix X3.

    1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

    D1599 Test Method for Resistance to Short-Time, Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1708 Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

    D1784 Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds

    D1898 Practice for Sampling of Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2581 Specification for Polybutylene (PB) Plastics Molding and Extrusion Materials

    D2749 Symbols for Dimensions of Plastic Pipe Fittings

    D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials

    D3915 Specification for Rigid Poly (Vinyl Chloride) (PVC) and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Pressure Applications

    D4181 Specification for Acetal (POM) Molding and Extrusion Materials

    F412 Terminology Relating to Plastic Piping Systems

    F699 Practice for Accelerated Conditioning of Polybutylene Pipe and Tubing for Subsequent Quality Control Testing

    F948 Test Method for Time-to-Failure of Plastic Piping Systems and Components Under Constant Internal Pressure With Flow

    ANSI Standards

    ANSI Z17.1 Preferred Numbers

    AWWA Standard

    Manual M-11 Steel Pipe Design and Insulation

    Federal Standard

    Fed Std. No. 123 Marking for Shipments (Civil Agencies)

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage

    NSF Standard

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D3309-96AR02

    Citation Format

    ASTM D3309-96a(2002), Standard Specification for Polybutylene (PB) Plastic Hot- and Cold-Water Distribution Systems (Withdrawn 2010), ASTM International, West Conshohocken, PA, 1996,

    Back to Top