If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM D3019 / D3019M - 17

    Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, and Fibered

    Active Standard ASTM D3019 / D3019M | Developed by Subcommittee: D08.05

    Book of Standards Volume: 04.04

      Format Pages Price  
    PDF 2 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 2 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 4 $54.00   ADD TO CART


    This specification covers the physical requirements and testing of three types of lap cement for use with asphalt roll roofing. Type I is a brushing consistency lap cement intended for use in the exposed-nailing method of roll roofing application, and contains no mineral or other stabilizers. This type is further divided into two grades, as follows: Grade 1, which is made with an air-blown asphalt; and Grade 2, which is made with a vacuum-reduced or steam-refined asphalt. Both Types II and III, on the other hand, are heavy brushing or light troweling consistency lap cement intended for use in the concealed-nailing method of roll roofing application, only that Type II cement contains a quantity of short-fibered asbestos, while Type III cement contains a quantity of mineral or other stabilizers, or both, but contains no asbestos. The lap cements shall be sampled for testing, and shall adhere to specified values of the following properties: water content; distillation (total distillate at given temperatures); softening point of residue; solubility in trichloroethylene; and strength at indicated age.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers lap cement consisting of asphalt dissolved in a volatile petroleum solvent with or without mineral or other stabilizers, or both, for use with roll roofing. The fibered version of these cements excludes the use of asbestos fibers.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 The following precautionary caveat applies only to the test method portion, Section 5, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D36/D36M Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

    D6511/D6511M Test Methods for Solvent Bearing Bituminous Compounds

    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30121601(Asphalt); 30151501(Roll roofing)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D3019_D3019M-17

    Citation Format

    ASTM D3019 / D3019M-17, Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, and Fibered, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top