| Format | Pages | Price |   |
![]() |
6 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 6 | $52.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
12 | $62.00 | ![]() |
Historical Version(s) - view previous versions of standard
More F17.65 Standards Related Products Standard References
Abstract
This specification covers the material, dimensional, and mechanical requirements, and the corresponding test methods for plain-end or bell-end styrene-rubber (SR) plastic drain pipes and fittings in 2 to 6 in. sizes that are suitable for nonpressure underground drainage of sewage and certain other liquid wastes, in applications outside the building limits, where dimensional stability, resistance to aging, and strong eight joints are required. The SR plastics shall contain styrene plastics combined with rubber (polybutadiene or butadiene-styrene type, or both) and compounding materials such as antioxidants and lubricants, and may contain acrylonitrile. When evaluated using the test procedures prescribed herein, the finished pipes and fittings shall conform to the following requirements: workmanship; dimensions such as socket and pipe diameters, wall thickness, laying length, socket depth, and dimensional stability; and mechanical properties such as impact strength, stiffness and deflection temperature, tensile strength and elongation at rupture, modulus of elasticity in tension, Izod impact strength, flattening resistance, solvent cement, and joint tightness.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, load-deflection properties, dimensional stability, and joint tightness of plain-end or bell-end styrene-rubber (SR) plastic drain pipe and fittings in sizes 2 through 6 in.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3122 Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
Military Standard
MIL-STD-129 Marking for Shipment and StorageICS Code
ICS Number Code 23.040.20 (Plastic pipes); 23.040.45 (Plastic fittings)
UNSPSC Code
UNSPSC Code 40171517(Commercial PVC pipe)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D2852-16
Citation Format
ASTM D2852-16, Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings, ASTM International, West Conshohocken, PA, 2016, www.astm.org
Back to Top