| Format | Pages | Price |   |
![]() |
5 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 5 | $52.00 | ![]() |
Historical Version(s) - view previous versions of standard
More D08.20 Standards Related Products Standard References
Significance and Use
5.1 This practice is for the sampling and analysis of existing built-up roof systems. For roofs under construction, use Practice D3617/D3617M.
1. Scope
1.1 This practice is a guide for removing test specimens from existing built-up roofing systems in the field and for determining the approximate quantities of the components of that specimen (Note 1). Components determined may be:
1.1.1 Insulation components when they are part of the roof membrane system,
1.1.2 Plies of roofing felt,
1.1.3 Interply layers of bituminous material,
1.1.4 Top coating, and
1.1.5 Surfacing.
Note 1: This procedure is for the investigation of existing roofs and is not intended for new construction inspection.
1.2 This practice is applicable to both 914-mm [36-in.] and 1000-mm [39 3/8-in.] wide felt rolls.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary information, see 6.3.2.1.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D226/D226M Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
D227/D227M Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing
D249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules
D250 Standard Specification for Asphalt-Saturated Asbestos Felt Used in Roofing and Waterproofing
D371 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules; Wide Selvage
D1079 Terminology Relating to Roofing and Waterproofing
D2178/D2178M Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D2626/D2626M Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing
D3158 Specification for Asphalt Saturated and Coated Organic Felt Used in Roofing
D3672 Standard Specification for Venting Asphalt-Saturated and Coated Inorganic Felt Base Sheet Used in Roofing
D3909/D3909M Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules
D4601/D4601M Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing
D4897/D4897M Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing
D4990 Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
ICS Code
ICS Number Code 91.100.50 (Binders. Sealing materials)
UNSPSC Code
UNSPSC Code 30151500(Roofing materials); 30121500(Bituminous derivatives)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D2829_D2829M-07R19E01
Citation Format
ASTM D2829 / D2829M-07(2019)e1, Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top