| ||Format||Pages||Price|| |
|3||$48.00||  ADD TO CART|
|Hardcopy (shipping and handling)||3||$48.00||  ADD TO CART|
|Standard + Redline PDF Bundle||6||$56.00||  ADD TO CART|
This specification covers prefabricated asphalt liner sheets intended for installation to provide a continuous, exposed lining for reservoirs, ponds, canals, and ditches. The liner sheets shall consist of layers of asphalt mastic between asphalt-saturated felts, mats, or fabrics, and shall be coated on both sides and covered with a material to prevent the finished sheets from sticking together during storage and shipment. The coating shall be a hot-applied asphalt material permitted to be compounded with a mineral stabilizer. Thickness of asphalt coating, water absorption, mass percent of asphalt, resistance to decay, flexibility, brittleness, and heat dissipation tests shall be performed to conform to the requirements specified.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers prefabricated bituminous geomembranes intended to provide a continuous, exposed lining for canals and ditches.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
D4354 Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing
D4439 Terminology for Geosynthetics
D4798/D4798M Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
D4833/D4833M Test Method for Index Puncture Resistance of Geomembranes and Related Products
D5147/D5147M Test Methods for Sampling and Testing Modified Bituminous Sheet Material
D5199 Test Method for Measuring the Nominal Thickness of Geosynthetics
D5261 Test Method for Measuring Mass per Unit Area of Geotextiles
D5884/D5884M Test Method for Determining Tearing Strength of Internally Reinforced Geomembranes
D6455 Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs)
D7275 Test Method for Tensile Properties of Bituminous Geomembranes (BGMs)
E96/E96M Test Methods for Water Vapor Transmission of Materials
ICS Number Code 91.100.50 (Binders. Sealing materials)
UNSPSC Code 30121701(Geomesh); 30121900(Soil stabilizers and reinforcing materials)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D2643 / D2643M-21, Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type), ASTM International, West Conshohocken, PA, 2021, www.astm.orgBack to Top