ASTM D2397 / D2397M - 20
Standard Specification for Cationic Emulsified Asphalt
| Format | Pages | Price | ||
 |
3 | $44.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 3 | $44.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
6 | $52.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More D04.41 Standards Related Products Standard References
Abstract
This specification covers the seven grades of cationic emulsified asphalt for use in pavement construction. The asphalt shall be homogeneous after thorough mixing provided separation has not been caused by freezing and shall conform to the requirements set for viscosity, storage stability, demulsibility, coating ability and water resistance, particle charge, and distillation.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers seven grades of cationic emulsified asphalt for use in pavement construction in the manner designated.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D5/D5M Test Method for Penetration of Bituminous Materials
D113 Test Method for Ductility of Asphalt Materials
D140/D140M Practice for Sampling Asphalt Materials
D244 Test Methods and Practices for Emulsified Asphalts
D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene
D3910 Practices for Design, Testing, and Construction of Slurry Seal
D6930 Test Method for Settlement and Storage Stability of Emulsified Asphalts
D6933 Test Method for Oversized Particles in Emulsified Asphalts (Sieve Test)
D6935 Test Method for Determining Cement Mixing of Emulsified Asphalt
D6936 Test Method for Determining Demulsibility of Emulsified Asphalt
D6997 Test Method for Distillation of Emulsified Asphalt
D7226 Test Method for Determining the Viscosity of Emulsified Asphalts Using a Rotational Paddle Viscometer
D7402 Practice for Identifying Cationic Emulsified Asphalts
D7496 Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer
D7553 Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
D8078 Test Method for Ash Content of Asphalt and Emulsified Asphalt Residues
ICS Code
ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D2397_D2397M-20
Citation Format
ASTM D2397 / D2397M-20, Standard Specification for Cationic Emulsified Asphalt, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top