ASTM D2028 / D2028M - 15 Standard Specification for Cutback Asphalt (Rapid-Curing Type)

ASTM D2028 / D2028M - 15

Standard Specification for Cutback Asphalt (Rapid-Curing Type)

Active Standard ASTM D2028 / D2028M | Developed by Subcommittee: D04.40

Book of Standards Volume: 04.03

Format	Pages	Price
PDF	2	$40.00	ADD TO CART
Hardcopy (shipping and handling)	2	$40.00	ADD TO CART
Standard + Redline PDF Bundle	4	$48.00	ADD TO CART

Reprints and Permissions

Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center

Rent This Document

Reprints and Permissions

Reprints, Permissions and Rentals

Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center

Rent This Document

Reprints and Permissions

Historical Version(s) - view previous versions of standard

ASTM License Agreement

Shipping & Handling

More D04.40 Standards Related Products Standard References

Abstract

This specification covers cutback petroleum asphalts of the rapid-curing type for use in the construction and treatment of pavements. The cutback asphalt shall not foam when heated to application temperature and shall conform to the requirements prescribed for the following: (1) kinematic viscosity, (2) flash point, (3) distillate content, (4) amount of residue from distillation, (5) properties of residue from distillation such as viscosity, ductility, and solubility in trichloroethylene, and (6) water content. The properties enumerated shall be determined by the specified test methods including tag open-cup flash point, distillation, and penetration tests.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers cutback petroleum asphalts of the rapid-curing type for use in the construction and treatment of pavements.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D5 Test Method for Penetration of Bituminous Materials

D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

D113 Test Method for Ductility of Bituminous Materials

D140 Practice for Sampling Bituminous Materials

D402 Test Method for Distillation of Cutback Asphalt

D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene

D2170 Test Method for Kinematic Viscosity of Asphalts (Bitumens)

D2171 Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

D3143 Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus

D7553 Test Method for Solubility of Asphalt Materials in N-Propyl Bromide

ICS Code

ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials)

UNSPSC Code

UNSPSC Code 30121604(Cutback products)

Referencing This Standard

Link Here

Link to Active (This link will always route to the current Active version of the standard.)

DOI: 10.1520/D2028_D2028M-15

Citation Format

ASTM D2028 / D2028M-15, Standard Specification for Cutback Asphalt (Rapid-Curing Type), ASTM International, West Conshohocken, PA, 2015, www.astm.org