| Format | Pages | Price |   |
![]() |
6 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 6 | $52.00 | ![]() |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More D08.04 Standards Related Products Standard References
Abstract
These test methods cover the sampling and examination of felts and woven fabrics, saturated or impregnated but not coated with asphaltic or coal-tar materials, for use in waterproofing or for the construction of built-up roof coverings. After appropriate sampling, representative specimens shall be examined for the mass of wrapping material and mandrel (core), net mass per unit area, appearance and dimension of rolls, detached comminuted surfacing, moisture, strength, pliability, and loss on heating. Consequently, desaturated felt or fabric shall be examined for weight, retained carbonaceous matter, total comminuted surfacing, bituminous saturant, thread count of fabrics, thickness of felts, and ash content.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 These test methods cover the sampling and examination of felts or woven fabrics, saturated or impregnated but not coated with asphaltic or coal-tar materials, for use in waterproofing or for the construction of built-up roof coverings.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D645/D645M Test Method for Thickness of Paper and Paperboard
D828 Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
D1079 Terminology Relating to Roofing and Waterproofing
D1682 Test Method for Breaking Load and Elongation of Textile Fabric
D1910 Methods of Test for Construction Characteristics of Woven Fabrics; Replaced by D 3773, D 3774, D 3775, D 3776, D 3882, D 3883
D4072 Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch
D4312 Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method)
ICS Code
ICS Number Code 91.100.50 (Binders. Sealing materials)
UNSPSC Code
UNSPSC Code 30151503(Roofing fabrics); 11162124(Felt fabrics)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/D0146_D0146M-04R20
Citation Format
ASTM D146 / D146M-04(2020), Standard Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top