ASTM D1369 - 19

    Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments

    Active Standard ASTM D1369 | Developed by Subcommittee: D04.24

    Book of Standards Volume: 04.03


      Format Pages Price  
    PDF 4 $44.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $44.00   ADD TO CART
    Standard + Redline PDF Bundle 8 $52.00   ADD TO CART



    Significance and Use

    4.1 This practice is intended to be used as a guide by those involved in the design of asphalt surface treatments. It covers typical application rates for the various types of surface treatments and covers aggregate sizes and recommended grades of asphaltic material for both hot and cool weather conditions.

    4.2 The typical asphalt material application rates given are for normal surfaces and non-porous aggregates. Provision is made for rate adjustment when other than normal surfaces or porous aggregates, or both, are involved.

    1. Scope

    1.1 This practice covers the rates of application of asphalt materials and aggregates and types and grades of asphalt materials for single and multiple asphalt surface treatments as applied to suitably prepared pavements or bases.

    1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C29/C29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate

    D8 Terminology Relating to Materials for Roads and Pavements

    D448 Classification for Sizes of Aggregate for Road and Bridge Construction

    D946/D946M Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction

    D977 Specification for Emulsified Asphalt

    D1139/D1139M Specification for Aggregate for Single or Multiple Bituminous Surface Treatments

    D1250 Guide for the Use of the Joint API and ASTM Adjunct for Temperature and Pressure Volume Correction Factors for Generalized Crude Oils, Refined Products, and Lubricating Oils: API MPMS Chapter 11.1

    D2027/D2027M Specification for Cutback Asphalt (Medium-Curing Type)

    D2028/D2028M Specification for Cutback Asphalt (Rapid-Curing Type)

    D2397/D2397M Specification for Cationic Emulsified Asphalt


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials)

    UNSPSC Code

    UNSPSC Code 30121500(Bituminous derivatives)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D1369-19

    Citation Format

    ASTM D1369-19, Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top