If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C357 - 07(2015)

    Standard Test Method for Bulk Density of Granular Refractory Materials

    Active Standard ASTM C357 | Developed by Subcommittee: C08.03

    Book of Standards Volume: 15.01

      Format Pages Price  
    PDF 3 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $46.00   ADD TO CART

    Significance and Use

    3.1 Granular refractory materials may be either refractory grain raw materials that are used in the manufacture of finished refractory products, or bulk granular refractory materials that are sold, with or without some degree of processing, to refractory consumers for various uses. In either case, characterizing the properties of a granular refractory material is essential in evaluating its quality or consistency of quality and in determining suitability for end use. One of the important properties is bulk density because of its relationship to end product quality, usage, and performance.

    3.2 The refractories producer can use this test method as one of the quality-control tests for his manufactured or mined refractory grain raw materials or for evaluating potential refractory grain raw materials.

    3.3 For the refractories consumer, the principal use of this test method is in the evaluation of the quality or the consistency of quality of the granular material in purchased refractory mixes or in bulk granular refractory materials used by the consumer.

    3.4 This is a primary test method, and thus is suitable for use in specifications, quality control, and research and development. It can also serve as a referee test method in purchasing contracts or agreements and as a base for development of more rapid, secondary test methods for use in quality control on manufactured refractory raw materials.

    3.5 Fundamental assumptions inherent in this test method are that the sample is representative of the material in general, the particle size of the sample is within the range specified by the test method, the material is not readily hydratable, and the size and quantity of pores in the material permits removal of surface water without drainage from the pores themselves. Deviation from any of these assumptions negates the usefulness of the test results.

    3.6 In interpreting the results of this test method, it must be recognized that the specific gravity of the material as well as the porosity affects the value obtained for bulk density. Thus, comparisons of results should only be made between like materials or with full recognition of inherent differences between the materials being compared.

    1. Scope

    1.1 This test method covers a procedure for determining the bulk density of granular refractory materials, commercial products which usually have particles that are retained on a 0.265-in. (6.7-mm) or coarser sieve.

    Note 1: This test method is not suitable for materials that hydrate in boiling water.

    1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.2.1 Exceptions—In Sections 4, 7, and 8, the apparatus used is only available in SI units.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

    ICS Code

    ICS Number Code 81.080 (Refractories)

    UNSPSC Code

    UNSPSC Code

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C0357-07R15

    Citation Format

    ASTM C357-07(2015), Standard Test Method for Bulk Density of Granular Refractory Materials, ASTM International, West Conshohocken, PA, 2015, www.astm.org

    Back to Top