| ||Format||Pages||Price|| |
|5||$54.00||  ADD TO CART|
|Hardcopy (shipping and handling)||5||$54.00||  ADD TO CART|
|Standard + Redline PDF Bundle||10||$64.00||  ADD TO CART|
This specification covers deals with air-entraining additions for use in the manufacture of air-entraining hydraulic cement. The materials used are: cement, aggregates, and reference addition. The grading requirements for fine and coarse aggregates are specified. The following are the test methods for cement samples: chemical analysis of cement, determination of addition in the finished cement, fineness of cement, normal consistency, time of setting, autoclave expansion, air content of mortar, compressive strength of mortar, and length change of mortar. Concrete mixture preparation, weighing, proportions, and mixing methods are detailed. The test on plastic concrete is done in accordance with the following methods: consistency and unit weight and air content. The following are tests for hardened concrete: compressive strength, flexural strength, and resistance to freezing and thawing.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers the requirements and methods for establishing the suitability of a material for use as an air-entraining addition to be interground with the clinker in the manufacture of air-entraining hydraulic cement conforming to Specifications , , and .
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C114 Test Methods for Chemical Analysis of Hydraulic Cement
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C150/C150M Specification for Portland Cement
C151/C151M Test Method for Autoclave Expansion of Hydraulic Cement
C175 Specification for Air-Entraining Portlant Cement; Replaced by C 150
C185 Test Method for Air Content of Hydraulic Cement Mortar
C187 Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste
C191 Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle
C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory
C204 Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C293/C293M Test Method for Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading)
C595/C595M Specification for Blended Hydraulic Cements
C596 Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement
C666/C666M Test Method for Resistance of Concrete to Rapid Freezing and Thawing
C1157/C1157M Performance Specification for Hydraulic Cement
ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
UNSPSC Code 30111600(Cement and lime)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM C226-19, Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement, ASTM International, West Conshohocken, PA, 2019, www.astm.orgBack to Top