If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C1840 / C1840M - 17

    Standard Practice for Inspection and Acceptance of Installed Reinforced Concrete Culvert, Storm Drain, and Storm Sewer Pipe

    Active Standard ASTM C1840 / C1840M | Developed by Subcommittee: C13.05

    Book of Standards Volume: 04.05

      Format Pages Price  
    PDF 9 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 9 $54.00   ADD TO CART

    Significance and Use

    4.1 The inspection of installed reinforced concrete pipe verifies proper installation of the product and establishes thresholds for comparison further evaluation.

    4.2 This practice is useful as a reference by an owner in preparing project specifications and to identify, evaluate and interpret observations during post installation inspections of pipe.

    1. Scope

    1.1 This practice covers the requirements for inspection and acceptance of installed reinforced concrete pipe by either person-entry, or remote inspection as shown in Figs. 1 and 2, respectively.

    1.2 The scope of this specification is intended for installation related observations and assumes that pre-installation inspection has been completed.

    1.3 The reinforced concrete culvert, storm drain and storm sewer pipe shall be manufactured in accordance with Specification C76, C506, C507, C655, or C1417 and accepted in accordance with AASHTO R073. This specification shall only be used for gravity, non-pressure storm drainage applications.

    1.4 Person Entry shall be used unless extenuating circumstances preclude this type inspection. Remote inspection is acceptable for use for pipe diameters of 30 in. [750 mm] and smaller unless otherwise specified by owner or engineer.

    1.5 Access of installed pipe for manual inspection shall follow OSHA 29 CFR PART 1926 SUBPART AA regulations for confined space entry. However, this standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.6 This practice does not cover deformation or deflection assessment. Concrete pipe is classified as a rigid structure because they do not bend or deflect appreciably under load before cracking. Due to these facts shape evaluation are of little or no value when evaluating concrete pipe.

    1.7 The values stated in either Imperial/US or [SI units] are to be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

    1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C76 Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

    C506 Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe

    C507 Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe

    C655 Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

    C822 Terminology Relating to Concrete Pipe and Related Products

    C1417 Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design

    D932 Practice for Filamentous Iron Bacteria in Water and Water-Formed Deposits

    ICS Code

    ICS Number Code 23.040.50 (Pipes and fittings of other materials)

    UNSPSC Code

    UNSPSC Code 40171510(Commercial concrete pipe)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1840_C1840M-17

    Citation Format

    ASTM C1840 / C1840M-17, Standard Practice for Inspection and Acceptance of Installed Reinforced Concrete Culvert, Storm Drain, and Storm Sewer Pipe, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top