| ||Format||Pages||Price|| |
|3||$41.00||  ADD TO CART|
|Hardcopy (shipping and handling)||3||$41.00||  ADD TO CART|
|Standard + Redline PDF Bundle||6||$49.20||  ADD TO CART|
This specification covers four types of pozzolanic hydraulic lime for structural purposes which include use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster. The four types of pozzolanic hydraulic lime are classified according to the minimum hydrated lime content, maximum hydraulic cement content, and specific performance requirements. Test specimens shall be stored in a moist room or cabinet wherein the storage surface shall be in equilibrium with the space to ensure no moisture loss. The specimens shall be subjected to testing to determine conformance to the following requirements: water soluble alkali, sulfur trioxide content, carbon dioxide content, fineness, maximum time of initial and final set, autoclave expansion, air content, water retention, and compressive strength.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This standard covers four types of pozzolanic hydraulic lime for structural purposes which include use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster.
1.1.1 PHL—Pozzolanic hydraulic lime for use in mortar, scratch, brown, and finish (stucco) coats of interior or exterior plaster.
1.1.2 PHLc—PHL with a maximum 20 % binder weight of hydraulic cement.
1.1.3 PHL-A—Air-entrained PHL.
1.1.4 PHLc-A—Air-entrained PHLc.
1.2 This specification classifies pozzolanic hydraulic lime by minimum hydrated lime content, maximum hydraulic cement content, and specific performance requirements.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime
C50 Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products
C51 Terminology Relating to Lime and Limestone (as used by the Industry)
C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
C114 Test Methods for Chemical Analysis of Hydraulic Cement
C150 Specification for Portland Cement
C207 Specification for Hydrated Lime for Masonry Purposes
C266 Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles
C270 Specification for Mortar for Unit Masonry
C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes
C595 Specification for Blended Hydraulic Cements
C778 Specification for Standard Sand
C1157 Performance Specification for Hydraulic Cement
ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
UNSPSC Code 30111603(Hydraulic lime)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM C1707-11, Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes, ASTM International, West Conshohocken, PA, 2011, www.astm.orgBack to Top