ASTM C1486 - 18

    Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings

    Active Standard ASTM C1486 | Developed by Subcommittee: D01.46

    Book of Standards Volume: 06.02

      Format Pages Price  
    PDF 4 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 8 $54.00   ADD TO CART

    Significance and Use

    4.1 Because the sample is prepared in a manner as it would be applied in the field, the test specimens may be considered representative of the application of a specified surfacing. Such methods include application by squeegees, rollers, trowels, notched trowels, and gage rakes.

    4.2 These systems vary in several ways, including the number of layers or application steps, the surface finish, and variation in composition.

    4.3 The results obtained in carrying out this practice should serve as a guide in comparing similarly applied surfacings. No attempt has been made to incorporate into this practice all of the various factors that may affect the performance of such applications when subjected to actual service.

    1. Scope

    1.1 This practice covers methods for preparing test specimens and testing procedures for broadcast or slurry-broadcast monolithic floor surfacings in areas where chemical resistance is required.

    1.2 These floor surfacings are applied by various application methods including squeegees, rollers, trowels, notched trowels, and gage rakes onto suitably prepared concrete substrates. The surfacings bond to the substrate upon curing to provide a nominal thickness of 60 mils (1.5 mm) or greater.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C413 Test Method for Absorption of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes

    C904 Terminology Relating to Chemical-Resistant Nonmetallic Materials

    C905 Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D1308 Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes

    D2047 Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine

    D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

    D7234 Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers

    E648 Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

    F2508 Practice for Validation, Calibration, and Certification of Walkway Tribometers Using Reference Surfaces

    NACE/SSPC Joint Standard

    NACE No. 6/SSPC-SP 13 Surface Preparation of Concrete

    ICS Code

    ICS Number Code 97.150 (Floor coverings)

    UNSPSC Code

    UNSPSC Code 30161700(Flooring)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1486-18

    Citation Format

    ASTM C1486-18, Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings, ASTM International, West Conshohocken, PA, 2018,

    Back to Top